Models > GCSE600 > Instructions

GCSE600 Maytag Cooktop - Instructions

Jump to:

All Instructions for the GCSE600
61 - 75 of 81
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Richard from Germantown, MD
Parts Used:
WPW10196405
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
old drip bowl was worn out
new drip bowl fit perfectly and was a snap to install.
Was this instruction helpful to you?
Thank you for voting!
Customer:
gene from kent, WA
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burner not working
burner was shorting out replaced part works great
Was this instruction helpful to you?
Thank you for voting!
Customer:
Earl from Union Mills, NC
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burner would not heat up the connection was bad
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kevin from Desoto, MO
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
two of the burners were working intermittently
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Chesapeake, VA
Parts Used:
330031
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dallas from Arlington, TX
Parts Used:
WPW10196405
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this instruction helpful to you?
Thank you for voting!
Customer:
gizella from mays landing, NJ
Parts Used:
WPW10196405
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old dirty drip pans
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Villa Ridge, MO
Parts Used:
330031
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from Staunton, IL
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Blair from Edmonds, WA
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Burned out surface element
I pulled the old one out and installed the new one. Never broke a sweat.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Tigard, OR
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
failed heating element
Took out of package and plugged in. turned on. It took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from Montgomery, AL
Parts Used:
330031
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Top element not heating
Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jennifer from Albion, NE
Parts Used:
WPW10196405
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Drip bowls tarnished.
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".
Was this instruction helpful to you?
Thank you for voting!
Customer:
vincent from Martinsville, VA
Parts Used:
330031
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
electric surface unit not working
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bonnie from Price, UT
Parts Used:
330031
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
stove burner no longer would heat up burner element
I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GCSE600
61 - 75 of 81