MGC4436BDC0 Maytag Cooktop - Instructions

remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan to complete repair.

I had used a pan too large for the middle burner - result: melted knob. Just pulled the old one off (up and straight) and then pushed the new one down firmly. Make sure the indicator line is pointing at you, so the flat side of the spindle matched the flat side of the hole on the knob. Easy peasy.

replaced grates

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

Overall, it was painless and easy with zero problems

Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.

I never did receive the part. It was a knob. Part numberPS11744700. Must've got lost in the mail. Thanks. Thomas Horne, 266 Eedmont Ct., Rogersville,Tn 37857?............P.S. The cost of it cleared my bank.

A very simple repair.
I inserted the brackets and screwed them in position

cut off terminals and replaced with the right size one's stove lights every time now wlrowe

The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..

Anyhow, thanks to the great part, the stove works really well again.

First step is to turn gas off to cook top and also disconnect power to the unit. Than using a crescent wrench disconnect the gas line going to the unit from the Regulator. Than again using the crescent wrench disconnect the regulator from the bottom of the unit. Next remove the nipple that connects the gas line to the regulator from the old unit. Apply new pipe dope to the threads and screw it into the new one and tighten down. Next install the regulator to the unit and install the gas line to the regulator. once done with the install you can now plug the unit in and turn on the gas. You are now ready to use the cook top again

removed rear cover where the spark module was and change it

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!