MLZ8505ADH Maytag Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from Pierce, ID
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The grommets came apart metal from rubber.
I replaced the broken grommets with the new ones. I purchased 8 so I would have back ups because I did not feel the new one would last either. I think they cost TOO MUCH but I could not haggle for price.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- j from bridgewater, NJ
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Sealed burner caps were rusted within and gas leak through the bottom of the caps
Just used a car oil filter band type wrench and rotated the sealed burner cap a 1/4 turn. cleaned up the rust and dirty. Replaced it with the new cap and tightened it with a 1/4 turn by hand. Instruction can be found on Maytag gas installation manual. The burners are working well and just like a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from wildomar, CA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
range top loose, grommets missing
very easy to push each grommet into range top holes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan Jose from Miami, FL
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burners corroed by sulphate in the gas
just turn the burners counter clock wise with the help of a jar opener pad. unplug the wire connectors and replace the burners no hassle, no problem. Everything went fine… one thing though, it is not the same color as it was before. I didn’t realize it until opening the box. Previous color was grey. My wife is Ok with it, so I won’t complain, but maybe you should add the color option if there is more than one choice.
Best regards.
Best regards.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Warwick, MA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
both burner heads would not ignite
Unplugged the burner heads from the wires, and simply put the wires on the new burner heads and put back onto the stove,. Simple as pie. Very happy that i found parts select online, easy to find the part though your pictures and easy to order.
Loved being able to do this myself without a middle man. Very satisfied!
Loved being able to do this myself without a middle man. Very satisfied!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hal from National City, CA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing gromet
Pushed into hole by hand, really simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- julie from harrodsburg, KY
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the burner cap on my maytag gas range was rusty on the inside and didn't allow the cap to sit flush-causing gas and flames to leak from under the cap
installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nataly from Brooklyn, NY
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of four burners did not start (no sparks)
Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alberto from Houston, TX
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were rusted and rotten from the bottom, flames were coming from around the bottom
all i did was twist the burner counter-clockwise unplug 2 wires and installed the new ones, real easy, it took me about 7-8 minutes for the 4 burners, that was all, our stove is working like new now, albert
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Jacksonville, FL
- Parts Used:
- WP7432P097-60, 74003944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
One of the posts was broken off of the igniter
Purchased the new, removed the old (2 phillips screws) and installed the new igniter. I was able to salvage one of the old wires by pulling the broken post out of the slip fitting. I ordered 3 new wires (at a later date) just in case. I think the only trick part of this job is to properly install the ignition knob, this is more than important. if installed incorrectly a person could damage the new igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Mission, TX
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
rusted out burner on stove top
turned burner counterclockwise and removed it reversed procedure and installed new one..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from SEARCY, AR
- Parts Used:
- 74003944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Inside Of Knob Busted Out, Would Not Turn Ignitor.
Actually too simply to list as diy job. Merely remove old knob and push new one onto spindle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brady from CARYVILLE, FL
- Parts Used:
- 74003944
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
igniter knob for gas stove stripped out
Slip old knob off slide new knob on, be sure to align knob properly your done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Appleton, ME
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner heads were rusted out, releasing flames from underneath and also clogged with carbon dust
Very simple! Unscrewed the burner heads with a simple twist, unplugged the two wires from the old head, plugged them into the new one, then screwed that back in. The flames are MUCH better - more efficient and safe. thank you! ( Only issue was when we ordered we didn't see a choice of color and the new ones are different, but it really doesn't matter on an older stove anyway.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from tisbury, MA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner cap had rusted out
It was pretty much a plug it in job
Was this instruction helpful to you?
Thank you for voting!