CAE1000ACB Maytag Cooktop - Instructions

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

Pulled out electric heating element and replaced with new. I have had this frustrating problem for 2 years and after replacing the elements they now work like new! My only question, why did it take me so long to replace???

just installed

Unplugged the burner units and replaced the drip pans. Five seconds time per burner.

I just pulled the electric element out of the slot and dropped the drip pan in place and slipped the electric element back in place and it was ready to go. It looks almost new. We built a new house in 95. It took 17 months to build it. I got the stainless steel cook top that you can have the grill on one side or you can pull the grill off and slip in the burners. It is only 4 burners but it is plenty to work with. It has a down draft.

Our old Jenn-air cooktop was at least 28 years old.They looked bad.We didn't see the need to buy a whole cooktop when the rest of the stove, fan,etc. still worked great. So I got on the Partselect web site and found a black radiant cartridge. It came exactly the day the said it would. I took out the old coil cartridge and plugged the new one. Lo, my stove now looks modern. We also ordered a terminal block. With this my husband repaired the old burned out coil burner and in about 20 minutes I had a spare to use with my canner. I really like the new cartridge and plan to buy another one. It was a pleasure to do business with Partselect.

replaced drip pans--they fit perfectly and look great!

Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

Removed screws by drilling one and using a pliers to remove 2nd one. At first did not have enough wire to pull recepticles out until I relized wires were clipped to back of range to hold in place. Unclipped wires, pulled recepticles out, cut wires and attached new recepticles by connecting wires with wire nuts (I think wire nuts were to small so I used my own a size larger). Another problem that I found was that the recepticles on my range were held in place only by the screws that attached the recepticles to the drip pan flang. I had to bend an L bracket to prop under each recepticle to hold the back of it up so the burner element would sit level over the drip pan.

pulled he cooktop, replaced the recepticles, reassembled.

It was a very easy project...Removed the stove top a few screws..snipped a couple of wires and attached the new receptacle...everything needed was in the package...They even have a video on here that was very helpful..shows how easy it really is...

Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done

Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.