MEC5430BDW Maytag Cooktop - Instructions

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

Opened the Cooktop. Hardest part was removing the cooktop.
The heating element was broken, very hard to see.

Remove 2 clips and install in new element. Great oppurtunity to clean the unit.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

My grandson, age 15 did the replacement. Now, how easy is that!

Not really a repair - just replaced some broken knobs - but pleasantly surprised how easy it was to match up to a fairly old cooktop. The local hardware stores that sell the tops don't stock simple replacement parts.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

Removed module replaced radiant element very easy repair.

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.

This is a slide-in range, so I:
1. Turned off the circuit breaker for the range. The range is hard-wired, so can't just be unplugged. I determined the clock on the range went off.
2. Removed 4 screws holding the front control panel to the cooktop. Removed 2 screws from each side panel into the cooktop. Removed 4 screws from the rear panel holding the cooktop.
3. With my assistant (my wife) lifted the cooktop and tilted it so that I could access the underside.
4. Used an iPad to take photos from several angles of the wire connections from each burner control. Printed the one showing the connections on the dual burner control.
5. Removed the 4 screws holding the sheet metal support for the dual burner and one of the other burners. Released the spring steel retainers holding the dual burner. Removed the burner.
6. Used the iPad again to take photos of the connections to the dual burner, and printed it.
7. Removed all the wire connections to the burner. Checked continuity from the center (common) terminal to each of the other terminals. Determined that in fact the inside coil was open (burned out).
8. Removed the two screws holding the spring clip retainers on the old burner. Matched the old and new burners to determine where the spring clips should go. Drilled 2 small holes in the base of the new burner and screwed the clips from the old burner on the new one.
9. Now the tricky part: The new burner didn't have the exact same limiter and heat sensor probe as the old one. After several false starts, we were able to barely make out the terminal letter/number designations on the control and match them to the same letter/numbers on the new burner. It required a magnifier and a strong flashlight to read these engraved markings.
10. Made the connections on the burner. I used a pair of long-nosed pliers to carefully pull the connections off the spade terminals, and attch them on the new burner.
11. Mounted the burner to the sheet metal support using the spring clips previously installed.
12. Re-attached the 4 screws holding the burner support to the cooktop.
13. Carefully replaced the cooktop onto the range, paying special attention to not pinching any of the wires, and making sure all the wires, from all the burners were still connected.
14. Replaced all 12 screws holding the cooktop to the range.
15. Turned on the power, and checked all burners, including the new one, to see if they were opetating properly. YAY! They all worked!

It must be noted that we had to call a repairman to troubleshoot our installation the first time. We had reversed two of the wires to the new burner, because of the difference between the old and the new limiter connections. The engraved markings in the porcelain were very difficult to see. The instructions that came with the new burner never addressed this issue, and instead had very confusing (and worthless) instructions about replacing the limiter from the old burner to the new on. (This was not possible, anyway).

After the repairman left, we discovered the front burner that had been working, no longer was. With our newfound experience, we repeated the previous steps to take the range apart and discovered one of the wires had become disconnected from that burner. We re-connected it, re-attached the cooktop, and everything worked.

One telltale indicator that we had mixed up the connections on the burner, was the red "hot' warning light on the range top came on as soon as we restored power, even though no burners had been on. I should mention that the dual burner "worked" a couple of times even with the reversed connections, but then failed to work any more.

This is a two module cook top That I have, 2 burners in each module. I took it apart take the damaged one out and replaced with the new one, put it back together and turn it on. Heeeyyyy it works. Thanks.(and I'm not an electrician)

Verified via ohmmeter that one of the two burners was open and not working. I also tested the switch and that appeared to be working okay. I then took out the old unit and compared it to the new one, and found that they upgraded the new unit. I followed the instructions to match the labeled parts and move the wire to the newer location of that. i.e the old one had 2B and 2A at the top and 1B and 1A at the bottom. The new one had 2B and 1B at the top and 2A and 1A at the bottom. It did come with wire extenders and insulated tubes on top of them, and extra to cover additional. After a couple of tries, I decided which wire I needed to use on which (small connectors to match small, and large to match large.) In a second try I decided to flip it over to have it face up instead of down. Overall, it worked out very well, and I was very pleased when I did the power up test and everything worked as desired.

looked on internet on how to remove top. an easy fix after watching video

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both side .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.