MGC5430ADQ Maytag Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dean from Mobile, AL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gas blowing out from under burners
As the video said, twist burner to the counterclockwise 1/8 turn. Lift the burner straight up. Disconnect the two wires. Remove the burner and reconnect the wires ( they only go one way so they cannot be connected backwards.) Place the burner over the gas fitting and turn the burner clockwise until snug. I turned the power off at the circuit breaker box. The video was extremely helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Stanwood, WA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted out burner
pull wire off of spark electrode unscrew old burner. screw on new burner attach wire to new spark electrode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Oconto Falls, WI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner flame was poor and yellow flames left sute marks on pots and pans
twist old burner and lift out disconnect two wires throw away gasket (if there is one left) connect two wires to new burner set in and twist till tight total time 45 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Plymouth, MA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber grommet for stove top cover
I ordered the grommet... Didn't match the others ... But it fit on , and will do the job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Vashon, WA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wore out burner and igniter
New burner and igniter.....actually it was very easy to to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bhavni from Richmond, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryl from San Pedro, CA
- Parts Used:
- WP3412D021-26
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
burners wouldn't light
First, only replaced the electrodes for lighting the stove burners. Nope, that wasn't the problem. Then replaced the burners -- that was the problem. Easy fix -- to bad I had to buy the electrodes first. Parts came in just a couple of days. Really surprised about how fast the parts shipped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Floral park, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the top broke away it was corroded
use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Soledad, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter not working
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Milton, NH
- Parts Used:
- WP3412D025-09, WP3412D021-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
flames coming out between burn head and stove top
removed old burns, cleaned built up rust from stove top, plugged wires onto igniter,adjust air gag on gas tube, installed burners on stove top, tested. replaced 2 burners in less then 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Fenton, MI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Flame coming from under burner cap
Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from San Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No ignition of gas stove burner
Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Midwest City, OK
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old burner's flame was coming out below the burner.
1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Millersburg, MI
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lost on of the Rubber Grommet holding the stove grate
So simple would be embarrassed to give any instructions; it is so self evident.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from Las Cruces, NM
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of top burner igniter
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3
Was this instruction helpful to you?
Thank you for voting!