MGC5536BDB Maytag Cooktop - Instructions

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

Took 5 seconds to replace these items! Shpping of the items was amazingly fast..2 days and we were back to new!

Put the new knob on

I just placed the knob on the burner control and pushed it in place. It was a really easy process. And thanks to you it was much cheaper ordering the part and putting it together myself than calling the repairman to order it, waiting for the part to come in and then making a service call to install it.

The spark module pulses a stepped up voltage to all four burner sparks at the same time regardless of which burner you want to ignite. I read that this part lasts about 10 years. I don't cook much and it lasted 13 years. On my Magic Chef the part is behind the right side wall panel. Lift the range top,remove all the screws that hold the right side panel in place. This replacement can done without opening any gas fittings.

The repair was so easily done, my grandson could have put the knobs on. I was so excited when the knobs arrived, I could not wait to put them on. I was like a little girl in a candy shop. Thank you very much!!

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

I removed the screws holding the burner covers which allowed me to remove the cook-top cover. Once opened I unplugged the connectors and slipped the switch assembly off. Once I had the new assembly I just slipped them back on. The only problems I had was 1) Some screws broke and I could not get them out. and 2) The ground connector was the wrong shape for my cooktop. It was round and my range has a flat connector, so I had to get a ceramic screw on wire connector.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.