CSG7000BAE Maytag Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Missing gasket under burner caused gas to leak out
I followed the video and it was incredibly easy. I shut the breaker off (we live in an apartment, and pulling the plug on the stove wasn't possible). I lifter out the old burner (the gasket underneath was corroded, and I just threw it out, as the newer burners are self-sealing); removed both the igniter wire and the ground wire (I needed a pliers to tug the igniter wire off); attached the new burner; replaced the burner; turned on the power; and voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from WATSONVILLE, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
BURNER DID NOT IGNITE. HOLE ON SIDE OF BURNER HAD A HOLE, SO FLAME WAS UNEVEN.
USED CHANNELOCK PLIERS TO ROTATE BURNER COUNTER-CLOCKWISE. PULLED OFF THE CONNECTORS, APPLIED RUST TREATMENT TO THE REPLACEMENT PART, WHICH HAD ITSELF STARTED TO CORRODE. SPADE LUGS ON THE OLD PART HAD A SPADE ADAPTER, BUT THE CONNECTION SEEMED TO WORK REGARDLESS OF THE MISS-MATCH. PART WAS REPLACED, TURNING THE BURNER CLOCK-WISE. VERY QUICK AND EASY REPAIR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from Dallas, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
burners would not light
replace burner-had to hit old burn with rubber mallet to break off grease and took old burner off-two wires were connected to it..put those on new burner and was done--have a little problem--flame is lower now than it was-but it turns on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Somonauk, IL
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove top burners ignition were not working
1st unplug stove opened cover to wireing box with a phillips driver removed old part transfered wires one by one installed new part installed cover & pluged in stove & worked line new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn Truax from Key West, FL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
All the burner caps had badly rusted; tip-off was the smell of gas.
Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Wheaton, IL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner would not lite. There was an intermittent spark from that burner.
Your site was easy to navigate, which made determining the problem from other customers easy, and choosing the correct part to replace the malfunctioning burner.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
The malfunctioning burner was easy to remove by twisting it a quarter turn counter clockwise, removing the two wires and replacing it with the new burner cap with electrode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dmytro from Brooklyn, NY
- Parts Used:
- 12001596
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
It didn't spark fire
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the six wires. Then I repeated those steps in back order. That's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Errol from Bay City, MI
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No spark at the burners
Replaced the ignition module with one from PartSelect. took care of the problem. They had the part in stock. Great service. Got the part in four days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Fort Washington, PA
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
no spark
Removed screws from back right of oven. Found spark module under right side panel of oven. Module connected in a slightly different way, so I had to drill a new hole and use a machine screw to secure it. All wires matched up exactly on new spark module. Replaced side panel, plugged it in and... SPARKS. Cheap and easy replacement and didn't have to call Maytag for repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from stratford, CT
- Parts Used:
- 12001596
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
turn on stove no spark to ignite the flame
I used the advise given in the website and it was very informative- the part was exactly where the folks on the website said it would be and although it wasnt the actual maytag part it was easily fitted by using the wire splices i mentioned and it was shipped quickly The whole process took less the 30 min once received. thank you for a very useful site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hastings on Hudson, NY
- Parts Used:
- WP7403P190-60, 12001596
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Burners would no longer work without using a match or lighter
I replaced all the burner switches as well as the spark ignition module. It was necessary to solder small terminals to use the existing wires with the new spark ignition module. Otherwise, this was a pretty straightforward job. My wife, an excellent cook, is now even happier than usual.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Lompoc, CA
- Parts Used:
- WP3424F005-81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I replaced the four Drip Pans on our Cooktop.
It was simple to remove the parts and then remove two screws and clean the area and re-assemble with the new drip pan. It was easier than I though it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ZHENG from PINOLE, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
repair range burner
in and out in 15 min ,is easy when part fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Floral park, NY
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
the top broke away it was corroded
use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bhavni from Richmond, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this instruction helpful to you?
Thank you for voting!