CEC1430AAW Magic Chef Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dallas from Arlington, TX
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed to replace to two 8* drip bowls on the kitchen range
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gizella from mays landing, NJ
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dirty drip pans
Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darwin from wisconsin rapids, WI
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emmett from Rayville, LA
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
unable to remove screw with screwdriver
used drill to remove old screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lodi, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Burner element stopped working
The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elroy from Atwater, MN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not operating or intermittently
Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lula from Antelope, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner did not heat
New receptacle element. I am a girl and I did it.!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosibel from Houston, TX
- Parts Used:
- WPW10196405, W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the old bowls were burned.
really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Euclides from Orlando, FL
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
on Indicator light on all time
Disconnect the range from wall outlet. remove 2 screws in the back of the cabinet,remove switch plug. connect back range to outlet to check if it is the switch. make sure the light isn't on. then I order the switch online at PartSelect.com and it arrived in 2 days. When I installed the piece, the problem had been solved. I hope this information will be helpful for others.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Summerfield, FL
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace 8" Element Switch
Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hedy from Richmond, VA
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I wanted to purchase new drip pans, since those that I have are a bit grimy
I will begin by saying that not only will I continue to order my parts from PartsSelect, but I also highly recommend this business. If you call Whirlpool be careful that they forward your call for parts to some preferred vendor, which a customer might assume is Whirlpool but it is not. PartsSelect is the same type of business, but with outstanding customer service. With regard to the drip pan, Whirlpool had not updated the part number for these as I found out when i called them. Whirlpool no longer uses the drip pans without the holes which is a serious problem since this could be hazardous to the owners of these ranges if you are forced to purchase the drip pans with the holes in them. That said, I ended up keeping my old drip pans, because if you spill grease under the new ones with the holes in them and since the range design with the fan built in on the top does not allow you to lift the top to clean under the pans, you could end up with a grease fire. This is not the fault of PartsSelect and they handled my order in a manner that I would give them a rating of exceptional for customer service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Milton, FL
- Parts Used:
- 7403P239-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Front burner would not heat properly.
Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald E. from Marissa, IL
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burners would not come on without moving them around
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vittorio from Wakefield, MA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Electric surface burner would only turn very hot
Well, I had to search a bit deeper in the internet to find out that the problem was not with the surface burner (which did look a bit burned out anyway) but rather with the surface burner switch (Part Number: PS336885) which must have ben damaged by the heat of the closest burner. If this problem would have been better documented (or if I would have searched more carefully) I would have saved over $40 with parts (Surface Burner Receptacle Kit) that I didn't quite need. Repairing the switch was very easy, thanks also to the available video , even though the stove used on this video (front panel) didn't quite match mine (top-back panel).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from San Francisco, CA
- Parts Used:
- 12001676
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Cartridge wire burned out
I was unable to remove the screw which held the electrical element.. so I took the new surface burner receptacle and removed the metal part, and used the old one and put in the new one in the old metal part and rewired, and it is like new.. now I need to do another one.
Was this instruction helpful to you?
Thank you for voting!