8351VV Magic Chef Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lesa from Orchard Park, NY
- Parts Used:
- WP74002115
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced Melted Knob
No repair involved. Just replaced a melted burner knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn Truax from Key West, FL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
All the burner caps had badly rusted; tip-off was the smell of gas.
Our handyman took off the burner caps and checked after we reported smelling gas. We ordered the replacements here, and they arrived by only the 2nd business day, instead of 3-5 as expected. The only hard part was scouring off the rust, with SOS pads, from the stove top before putting on the new burner caps (a simple plug-in)!! This is very important to check on your stove; you could blow-up your house! The gas was escaping under the old burner cap, through the rusted-out portions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from san jose, CA
- Parts Used:
- WP3412D024-26, 74002138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not start.
Removed and replaced old burner. ck'd ok.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilber from oshkosh, WI
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
terminal spade wrong size on range wiring to fit module
cut off terminals and replaced with the right size one's stove lights every time now wlrowe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bronius from College Station, TX
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Intermittent but rare spark when I went to start the rage: spark module definitely was toast or on its way out
The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..
Anyhow, thanks to the great part, the stove works really well again.
Anyhow, thanks to the great part, the stove works really well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Midwest City, OK
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old burner's flame was coming out below the burner.
1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Aberdeen, MD
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
power boost burner went up and all my burners got very rusty on the underneathe side
We were at a loss for a long time without my boost burner and then while checking all the rest of the burners my husband discovered that all of them had a massive amount of rust on the underneathe side of the burners and that worried me. Well as usual my husband took care of my worries when he discovered Parts Select. We both were pleasantly surprised when we found out that you had what we needed. And the installation was less than 5 minutes, WOW, THAT WAS GREAT! Thanx a million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Oxford, MA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottm Of Burner Rusted Out
Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Soledad, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter not working
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Fenton, MI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Flame coming from under burner cap
Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from San Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No ignition of gas stove burner
Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Brockway, PA
- Parts Used:
- 8215557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
range- top four burners will not light
removed rear cover where the spark module was and change it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Mobile, AL
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Gas blowing out from under burners
As the video said, twist burner to the counterclockwise 1/8 turn. Lift the burner straight up. Disconnect the two wires. Remove the burner and reconnect the wires ( they only go one way so they cannot be connected backwards.) Place the burner over the gas fitting and turn the burner clockwise until snug. I turned the power off at the circuit breaker box. The video was extremely helpful.
Was this instruction helpful to you?
Thank you for voting!