8361RV Magic Chef Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerald from Loveland, OH
- Parts Used:
- W11170853
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench (Adjustable), Wrench set
Missing regulator when floor model gas cooktop was purchased
1. Apply gas pipe joint sealer to treaded nipple on bottom of cooktop; 2. Install regulator on nipple with regulator direction arrow pointing to top of cooktop; 3. Tighten but do not overtighten as it may crack the aluminum body regulator; 4. Make sure the face of the regulator with the green painted surface faces the outside of the cabinet; 5. Get a new gas flex hose to connect to gas pipe (got mine at Lowe's - 2 feet long with all the right fittings for about $15). 6. Follow instructions on gas flex hose - make sure you use gas pipe joint sealer only where indicated; 7. Turn gas shutoff valve back on and test for leaks using soapy water; 8. Turn on each cooktop burner to bleed out air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ZHENG from PINOLE, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
repair range burner
in and out in 15 min ,is easy when part fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Vashon, WA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wore out burner and igniter
New burner and igniter.....actually it was very easy to to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Lompoc, CA
- Parts Used:
- WP3424F005-81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I replaced the four Drip Pans on our Cooktop.
It was simple to remove the parts and then remove two screws and clean the area and re-assemble with the new drip pan. It was easier than I though it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bhavni from Richmond, TX
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burners won't light up
We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Oxford, MA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottm Of Burner Rusted Out
Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Soledad, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter not working
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Fenton, MI
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Flame coming from under burner cap
Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from San Francisco, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No ignition of gas stove burner
Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Santa Barbara, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old burner was rotten and leaking
Pulled up the old burner, disconnected the ignition wires, re-connected them to the new burner, replaced the new burner in the stove and presto - everything worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from massillon, OH
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The igniter on my stove wouldn't ignite.
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete di from San Diego, CA
- Parts Used:
- WP3412D024-26
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner rusted, flame bypassing
Simply twisted to remove from range top, slipped off igniter wires, attached to new burner, and twisted back into place on range top. Works great,
Was this instruction helpful to you?
Thank you for voting!