CLZ8505BDT Magic Chef Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- tao from Frisco, TX
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the shell if the igniter was broken
find the part (image is really helpful), buy, and replace. Like I said, it's really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from WOODBURN, OR
- Parts Used:
- 74004053
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Back burner would not light
I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from brooklyn, NY
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner very hard to get out
Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Kelseyville, CA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ceramic on spark igniter broken
Pulled cooking grate off, twisted burner head counter clockwise 1/8 of a turn, pulled up and out. Removed 2 connecting wires.put new burner head on in reverse order. Simple about 2 minutes including opening box.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Flora from Lansdale, PA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Flames were coming out from under the burners. The bottom of burner was rusted
I ordered the two replacement burners. When they arrived I equipped myself with WD-40 spray, rubber mallet and a rubber gripper I used to use to open canning jars. Sprayed the WD-40 around the burner base and let it sit for 20 minutes. Made a mental note of the location of the sparker of the burner, to remember to put the new one in the same way. Gathered my courage and gently wacked the burner with the mallet all around it. Then grabbed the burner with the gripper and gave it a firm ¼ circle twist counter clockwise. It came apart with no problem. Disconnected the two electric wires by slipping them off their sockets. Removed all the loose rust and cleaned around the burner. Reconnected the wires with the new replacement burner and dropped it in its place. Wiggled it a little until it fit back into its original location and twisted it ¼ circle clockwise. Done, just saved myself the price of a new stove! Note: There is no need to shut off the main gas valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Godfrey from Las Cruces, NM
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement of top burner igniter
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Elizabeth, CO
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
range top was missing one of the rubber grommets used to hold the grate.
Just pushed the new grommet into the hole. The grommet fit just fine and took about 10 seconds to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Stanwood, WA
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted out burner
pull wire off of spark electrode unscrew old burner. screw on new burner attach wire to new spark electrode.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Plymouth, MA
- Parts Used:
- Y8007P02060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rubber grommet for stove top cover
I ordered the grommet... Didn't match the others ... But it fit on , and will do the job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruben from El Paso, TX
- Parts Used:
- WP3412D025-09
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Burners were not working properly. They had rusted out.
First I turned the burner head counter clockwise, lifted it out and pulled the connectors off. Then I connected the connectors back on the prongs of the new burner head and placed it back on the gas line and turned the burner head clockwise. I then turned the pilot light and and tested the connection. It worked without any problems. I then proceed to replace the second burner head using the same steps as on the first burner head.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Vancouver, WA
- Parts Used:
- WP74002414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rotating ignitor knob on my RV stove broke
The old knob simply slides off the shaft. I aligned the fins on the back of the new knob with the grooves on the shaft of the ignitor and pressed the new knob on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Casey from Soledad, CA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Igniter not working
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Was this instruction helpful to you?
Thank you for voting!