KECC507RBL06 KitchenAid Cooktop - Instructions

Unplugged the power cord first. Opened oven door and removed the two screws that held the stove top glass down. Lifted the glass top and removed the four wires connected to the element. I taped the wires to the lid in the pattern they were attached to the element. remove the element from the brackets. The new element was an exact match. reversed the sequence. Put a pot of water on and boiled a hot dog! Perfect! Great part and speedy delivery!!

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

Element was sent by buyer, As they recommended, when model of stove given to them. It was upper right rear. When element came. First took off old element. ...Match both element , new element did not look exactly the same, small variation. It did not come on.. I moved old element from left side to right side . Old element worked on both side .. tried new element on left side also.. still didn't work.. so I called right away and explained.. new element did not work.. not defective, but, just wasn't the right one.. I had a specialist came and check it out also. I was told wrong element.

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

I found on youtube Also we marked each wire with masking tape 1A and 1B, 2A and 2B. The wires were the same color.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.