KGCD807XBL00 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Katherine from dayton, WA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Burner Knob broke at the shaft
Simply took off the original knob and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Glenwood Springs, CO
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One burner not lighting, but has spark
Electrode ceramic was chipped. Spark was not coming to the top of the electrode, and stove would not light. Remove two burner screws. These are "baked" on...so use some liquid wrench first if you have it. Don't strip the head, or you'll have a mess. Remove burner, unplug electrode, remove electrode screw, replace electrode. Reverse process and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sanbornton, NH
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Monee, IL
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner did not light
Ordered online Tuesday, delivery by FedEx on Wednesday. Removed the old "popped" in the new and it worked right away. It was that simple. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from Mahtomedi, MN
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs were damaged/distorted due to wear
Pulled off the old knobs, pushed the new ones on. Could not have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Whitesboro, TX
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Burner Knobs would crack in the middle
The original knobs were poorly made and kept braking. After the third set, which were very expensive for some plastic knobs, I read this web page for help. Based on what I learned and what I read, I glued the metal sleeve in the knob shaft with some super glue. I then wrapped the shaft with copper wire and spread some industrial glue over the copper wrapping, which looked like a spring around the shaft. I have had no problems in the last month. I hope it keeps up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Boardman, OH
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann P from San Antonio, TX
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic burner knobs were split and would not let you turn burners off and on
I ordered an entire new set even though I only needed 2...removed all of the old ones, threw away the broken ones and installed the entire set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lakeside, Arizona, AZ
- Parts Used:
- WP74009336, WP8273062
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Igniter did not work
Bought The burner with the electrode already installed. The only way to go, since the screws will not come out without breaking. Also purchased two torx screws as thay also broke. A bad design by the manafactor.Had to drill and tap out for new torx screws to fit into the gas houseing. PartSelect had all the parts I needed. Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Two Rivers, WI
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Igniter Needed Replacement
Removed the burner & igniter as a unit. Screws holding burner down were very tight. One came out with effort, the other one the head broke off. Tried heat but to no avail. The screw holding the igniter had to be drilled out. Fortunatly I work in a machine shop so I was able to remove the screw, but the hole was then too large for the replacement screw. I wound aluminum foil around a toothpick to form a bushing in the hole so the screw could grab. Same principle as those plastic anchors for plaster or drywall. Bought stainless screws, but did not even try to get the broken screw out of the cooktop. The one screw holds it in place just fine. Wife is very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Elizabethton, TN
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked knob
Pushed the knob down on the spindle. Second order in three years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from Flower Mound, TX
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Former Burner Knob was broken
Pulled old ones off and replaced new ones by pushing them on the spindles. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrisville, RI
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The female D stem fitting of the control knob cracked, we could not turn on / off or control temperature to that heated area.
We replaced the control knob with an exact replica from PartSelect at a very reasonable price – Thank you.
Was this instruction helpful to you?
Thank you for voting!