KGCD807XBL00 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Tracey from Cypress, TX
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Knob stipped out
Simple repair to replace stripped out knob. More importantly we ordered the part over Christmas and it arrived within 2 or 3 days
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mayela from Plano, TX
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
2 of the old knob broke from my stove and look over the part from part select.com, it was very easy to find, good price and was delivered in 2 days. The service was outstanding.
I actually did it manually. It was fast and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from San Marcos, CA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old burner knobs had cracks
Removed the old burner knobs by hand, and replaced them with four new knobs.....
Real Easy!!
Real Easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from SCHWENKSVILLE, PA
- Parts Used:
- WP74009336
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would not light
removed the two screws holding the burner to the cooktop, disconnected the wire clip from the electrode then removed worn out electrode from burner. Re-attached the new electrode to the burner, re-attached the igniter wire then put the burner assembly back onto the cooktop
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from SUMMERVILLE, SC
- Parts Used:
- WP74009336
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Six burner gas cooktop, two units not lighting properly
It was very simple two Phillips head screws to remove the burner and one screw to remove the ignitor. It was probably less than a 5 minute job per burner. Unfortunately one burner had a very rusty screw holding the ignitor and the head stripped out. I tried a stripped screw removal tool with no success so I used a drill press to drill the screw out. It still took less than 30 minutes. Now both burners work like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manish from Los Altos, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Stove knobs broken, couldn't turn stove on
To be honest, it was nothing much. Had to reach and remove metal collars that were left behind around the pins, with needle-nose pliers. Put in the new knobs, and we were done.
What really left me impressed was 1) that the rep sent me pictures of the suspected knobs over email so I could identify them easily, and 2) I was expecting to wait for a week but I had the parts the next afternoon!!
What really left me impressed was 1) that the rep sent me pictures of the suspected knobs over email so I could identify them easily, and 2) I was expecting to wait for a week but I had the parts the next afternoon!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elena from Chandler, AZ
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken burner knob
just replaced with a new one. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Syracuse, UT
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Knob Melted
Pulled the old one off, pushed the new one on. Super easy. Simple ordering, quick processing and delivery. Way to go PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- susan from norfolk, VA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken burner knob
The hardest part was finding the part number...and that wasn't all that bad. Perfect match; perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W E from Camden, NC
- Parts Used:
- 74007736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
electrode sparked but not enough to lite burner
Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mentor, OH
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Knobs on the new JennAir Range I just purchased started to melt and when they were called they did nothing about it. I had to call and get new knobs at my cost.
Very easy, just removed the old ones and the new ones just clicked on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from san juan bautista, CA
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
erratic spark from electode,gas would no ignate.
Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CONCORD, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Weak spark for igniting gas burner.
Removed the gas deflector; unscrewed the burner body; pulled off the ignition wire; unscrewed the bad electrode; screwed in the replacement electrode; reversed the steps. Voila! Perfect operation once again. My one mistake? Ordered the wrong electrode initially. Make sure you get the right part the first time around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SPRING HILL, KS
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the knobs had broken
parts came on time and the repair was just remove the old and replace with new.
Was this instruction helpful to you?
Thank you for voting!