KECC502GWH2 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from Northfield, MN
- Parts Used:
- 8203534
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
stem of left front switch broke off.
Removing the stove top was easy, it was just setting in place. Put some blankets over the kitchen island and did the repair their. Most difficult thing was, how stight the wires were. After removing the switch cover, I wound it nessary to remove the inside side wall of the switch box in order to have enouph room to change the switch. Works just fine now. Thanks for your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Brevard, NC
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burned out heating element for radiant heat burner
I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Midlothian, TX
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Surface element was out
Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
Dual Burners both came on when switch was turned on to high heat, 6" burner safety feature to push switch down did not work.
Dual Burner switch was a replacement and not the same as original - instruction sheet gave excellent replacement instruction with color coded wires and numbers too follow, 6" switch was same as original so no problem with either switch replacement - stove now works like it was new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from La Grange Park, IL
- Parts Used:
- 8203534
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Switch did not turned off the element
Removed glass surface and identified existing wiring (sketch, photo, schematics) before disconnecting and removing it. Installed the new switch and connected the wires using the supplied wiring instructions as well as my sketch and schematics. Appreciate that the new switch came with wire extenders and shrink tubing. Had to use both of them.
Replaced the glass top and installed it back into the counter ,Turned on the circuit breaker and everything worked perfect. Just want to mention that I am extremely satisfied with PartSelect service. It is second time I ordered cooktop part. The delivery is prompt and the parts work as required
Replaced the glass top and installed it back into the counter ,Turned on the circuit breaker and everything worked perfect. Just want to mention that I am extremely satisfied with PartSelect service. It is second time I ordered cooktop part. The delivery is prompt and the parts work as required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Herriman, UT
- Parts Used:
- W10823711
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner not heating up
first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to the new element. (always mark down where the wires went)
Was this instruction helpful to you?
Thank you for voting!