KECG260SAL1 KitchenAid Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- George from ST. Charles, MO
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no heat from burner
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from reading, MA
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
contacts had gotten burnt out/blackened with age so burner was intermittent.
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Tucson, AZ
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner replacement
Pug it in! That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Versailles, IN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
large burners not working
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so you have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dicky from mcrae, AR
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replace burner coil connector
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be sure and disconnect power before starting!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Rochester, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
old bowls could not be cleaned. These new bowls make the stove look great
Removed old bowls and replaced with the new bowls. Also, thanks for your help with the rang knobs. You did not have the replacement knobs for my range but you gave me help in where I might get them. With the new bowls and knobs the range looks like new. Thanks again for all your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Chesapeake, VA
- Parts Used:
- 330031
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Edgewater, MD
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Drip Bowls
Lifted out the old ones and inserted the new ones and my range top looks brand new now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Viroqua, WI
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
none
I pulled out the burners, cleaned up the crumbled drip pans ,installed the new drip pans, pluged in the burners and was finished in about 3 minutes. I will order again from you. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teresa from Kasson, MN
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Surface burner block corroded
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James J from Sweet Grass, MT
- Parts Used:
- 330031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Blocks were broken
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from EL DORADO HILLS, CA
- Parts Used:
- WP3177565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
power burner warped, welds broken
just pulled and removed the old burner then pushed the two new power connections into same place - no tools - works perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Albany, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my drip bowls were old an I was unable to clean them
I took the old drip pans out and replace them with the new ones. Now my stove looks brand new. These were a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Kings Park, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace drip bowls
I took the old bowls out and dropped the new bowls in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Falls Village, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner stopped heating
Unplugged the old one and plugged in the new, which you sent promptly. No tools. Easiest fix ever.
Was this instruction helpful to you?
Thank you for voting!