62922113 Kenmore Cooktop - Instructions

Replaced the switch.

I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Turn off the power!!! Remove two screws from back of switch section and pull toward you. That was the tricky part; it wasn't obvious to me how to remove the section. Then simply revmove the witres from the old switch one by one and put them on the new part. Close it up and you're good to go.

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

Read privious fixes. Didn't know which control was bad but ordered two new ones. Marked locations of switch contacts and wire colors. Removed old controls. Installed new replacements and everything works fine. Thanks.

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Turn off circuit breaker to cooktop. Remove 2 screws that hold switch plate assembly.Remove tinnerman nut from old switch using adjustable wrench. Remove one wire at time from old switch to same location on new switch. Return shaft back through hole and replace nut, be careful to not overtighten. Replace control know, turn circuit breaker back on and test. Works like new. Neil

I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them in the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.

The repair was easy. First, I turned off cooktop circuit breaker. Then, removed the burner switch panel and the nut securing burner switch to panel. Disconnected the wiring and refit with new switch. Install switch panel and turned power back on. Now it's time to cook some dinner. Let's eat. :)

I purchased a replacement. I unplugged the cooktop. Unscrewed the little instrument panel and pulled it out. Turning over the panel, I noted the wires to the switch and photographed them in case I need to check them later. I pulled them off of the old, broken switch and put them onto the new switch, one at a time so that I couldn't get them messed up. Once all of the wires were switched, I removed the old switch and put on the new one. I then plugged in the model and tested the switch. It worked perfectly! IMPORTANT: I then tried to slide the panel back into the cooktop but forgot to unplug it first. This was a huge mistake, causing a nasty flash of electricity and smell. I unplugged the cooktop, put the panel back in, and replugged the cooktop. It worked, fortunately. Moral: ALWAYS unplug the damned cooktop when working on it!

We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.