9114398611 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from south bristol, ME
- Parts Used:
- WB30X254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner broke apart under a pot
Pulled out the burner. Just pulled and out it came. Looked you up online. Crawled around on the floor trying to find the model number. (This was the hardest part of the whole process.) Ordered the part; it came the very next day despite the fact that I didn't order special shipping. Unpacked the part, plugged it in. And it worked!!!!
FABULOUS service. Thank you so much.
FABULOUS service. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audret K, from San Diego, CA
- Parts Used:
- WB30X254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
metal "Y",shape metal long arm attached to burner came loose.holding the coil to burner
just plugged in the two prings into burner into outlet. Very simple and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from Quakertown, PA
- Parts Used:
- WB30X253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Heating Element's Contacts Were Burnout
Quite simple, just plug-in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lelia from Vienna, VA
- Parts Used:
- WB17X210
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was unreliable...would stop working...I had already replaced the burner
I did as the video suggested.....I cut the old wires and spliced new ones already attached to the new terminal block. It would have been nice to have some instructions with the parts as I expected one piece but had to connect the wires to the new block and the new metal cover. I was guessing a bit. Also, I needed to use the holder strip off my old part so that it displaced the new part back far enough to insert the burner connections. That meant finding a screw and nut small enough to allow the metal cover to fit on the block. But the burner works great. I've learned that any repair requires some ingenuity.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Montoursville, PA
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Right Front [surface burner terminal block kit]
We did the repair by following the inclosed instructions. we are elderly retired average ages 82. This was our first repair and it went very well. We are so pleased to have saved over $80.00 compared with hired labor 3 yre. ago for the same part. Thanks so much for your good service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Addison, TX
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Original burner switch fell apart
Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring the original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Graham from Bridgeville, CA
- Parts Used:
- W10900107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic post for knob broke off
I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of her own plumbing and other household repairs. The repair took less that one minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann B from Hueytown, AL
- Parts Used:
- WB32X106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Finding a drip pan that fit so that pots could sit level.
Ordered the drip pan from ParSelect.com. Unplugged element and took out old pan. Placed new pan in and replaced element. For the first time in many years, the part fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bennington, VT
- Parts Used:
- WB30X253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner not working light not working
changed burner and replace light receptical. easy job great service from supplier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald L. from Cedaredge, CO
- Parts Used:
- WB17X210
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the wires were not long enough to use the original path.
the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.
Was this instruction helpful to you?
Thank you for voting!