62942865 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jim from Two Rivers, WI
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad burnes off on switch
Easy as Pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vanna from St. Johnsbury, VT
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front right burner did not turn on
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Was this instruction helpful to you?
Thank you for voting!
burner connecters lost contact
pulled he cooktop, replaced the recepticles, reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Collegeville, PA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner only operated on high, no medium or low heat.
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Sherman, TX
- Parts Used:
- WP7518P054-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
a few months ago, my daughter-n-law and I were hitting up tacos on the grill----the grates melted ---I thought I would have to purchase all of the parts even though only the grates were ruined---I am very pleased with my find with you.
just laid them down on top of burner and coals,----easiest installation ever----We are already grilling ----this is just like grilling outside but in AC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Attleboro, MA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner would stay on high, on all settings.
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.
Thank you for your help!!
Bob
Thank you for your help!!
Bob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Woody from New Castle, VA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner always on high, no temp. adjustment.
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John J from Coatesville, PA
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Porcelan Electric Burner Plug broke
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Bothell, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rear butner no longer worked after liquid was spilled on range.
Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Jenkintown, PA
- Parts Used:
- WPY04100166, 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
One electric burner was not heating.
I simply watched the video on the PartSelect site. That made the repair easy and fast. It took perhaps 5 minutes to bring the stove back to life again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Port aransas, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rear Burner Was Not Functioning
Used a multimeter to determine that power was going to the surface burner infinite switch. Then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to torx head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed torx screws in the new switch and installed all screws back into range top. Reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Woodland Park, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner was very hot regardless of setting
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darwin from wisconsin rapids, WI
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Not heating
Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald E. from Marissa, IL
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burners would not come on without moving them around
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing
Was this instruction helpful to you?
Thank you for voting!