91143475890 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Shaohui from East Lansing, MI
- Parts Used:
- WB17X210
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Mont Belvieu, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Carthage, NY
- Parts Used:
- WB30X253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Large burner would not heat
I ordered the wrong part to start with. (READ CAREFULLY!) I reordered the correct part and it was simple. I unpluged the old element, plugged in the new one replaced the drip pan and trim ring and we were back cooking.
Service was fast, lady I spoke with on the phone to exchange parts was knowegable and nice. Great people to deal with.
Service was fast, lady I spoke with on the phone to exchange parts was knowegable and nice. Great people to deal with.
Was this instruction helpful to you?
Thank you for voting!
Previous home owners replaced 3 drip bowls with wrong style
I removed the heating elements and the drip bowls (wrong style). I then positioned the correct drip bowls on the stove and reinserted the heating elements. I snapped the heating coils into the small slots on the far side of the bowls to make sure that the heating elements would lay flat.
The whole process took less than 2 minutes.
The whole process took less than 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from HOUSTON, TX
- Parts Used:
- WB17X210
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Old Terminal Block was arcing.
Cut Wires to old terminal block and wired in new Terminal Block
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from HUNTER, OK
- Parts Used:
- WB23K5043
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
switch was weak.
Open top by reaching through a burner hole after the power has been disconnected at the fuse box. Take 4 1/4 screws out. take 2 phillips screws out of old switch. Take wires off one at a time placing them on the new switch. as an added precaution take a picture with your phone. Replace screws and lower top to working position. Replace knobs on stems and turn back on the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Danbury, NC
- Parts Used:
- WB30X253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old unit was bent and didn't work properly
I unplugged the old unit and plugged in the new one! It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from south bristol, ME
- Parts Used:
- WB30X254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner broke apart under a pot
Pulled out the burner. Just pulled and out it came. Looked you up online. Crawled around on the floor trying to find the model number. (This was the hardest part of the whole process.) Ordered the part; it came the very next day despite the fact that I didn't order special shipping. Unpacked the part, plugged it in. And it worked!!!!
FABULOUS service. Thank you so much.
FABULOUS service. Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
Blackened and rusted drip bowls on range.
Pulled out heating elements, removed old drip bowls, replaced with new drip bowls, re-connected heating elements. Done! Looks like a new stove!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Wellton, AZ
- Parts Used:
- WB31K5025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stove top in rental home missing a chrome drip bowl
I installed the chrome drip bowl and plugged in the burner to make sure that it worked. Voila!! everything is now perfect and i have a happy renter. thank you so much for your fast delivery.
Was this instruction helpful to you?
Thank you for voting!
Slot to small
What I had to do was open the slot for the burner pan more as it would not fit properly in. So we snip the burner pan a little and now it fits great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audret K, from San Diego, CA
- Parts Used:
- WB30X254
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
metal "Y",shape metal long arm attached to burner came loose.holding the coil to burner
just plugged in the two prings into burner into outlet. Very simple and quick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuel from Quakertown, PA
- Parts Used:
- WB30X253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The Heating Element's Contacts Were Burnout
Quite simple, just plug-in the new one
Was this instruction helpful to you?
Thank you for voting!
scorched burner drip bowls, plating peeled
It only took a few minutes to remove the old drip bowls and insert the new ones. No harder than cleaning! It's nice to cook things on my range now and not have drip bowls with scorched on food causing a fire hazard or setting off the smoke alarms.
Was this instruction helpful to you?
Thank you for voting!