91133255592 Kenmore Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jimiego from San Diego, CA
- Parts Used:
- WB24K5083
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burner would not light
replaced switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Longmont, CO
- Parts Used:
- WB13K18
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
would not ignite
It was so easy.I removed the old part with the new with pliers. Voila/// it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ivon from MIAMI, FL
- Parts Used:
- WB31K5092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner Bowl Rust Around The Edge
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. . . ) It was like drinking juice
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Laguna Hills, CA
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Left rear burner would not light
Began by removing the front panel where the range handles are located. There were 7 screws located under the panel which required opening of the oven hood. All of this removal was a waste of time, because the range top was on hindges. The only thing holding ithe range top down was the accumulated grease and oil along the edges. I used a screwdriver to sperate the range panel. There were side supports to hold the the top up, like a car hood support. Replacing the electrode was a snap after that. Overall, it took less than 30 mins but it would have taken less than 10 if I hadn't removed the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Jenison, MI
- Parts Used:
- WB13K18
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no spark at burner
Remove grates,pans and disk. Remove allen screws at each burner. Take a flat blade screwdriver and press in on tabs on each side of front of stove to depress keepers and lift top up. Remove wire, and keeper on bottom of electrode. Reverse for install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Valencia, CA
- Parts Used:
- WB31K5092
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Wanted to replace old burner bowls on stove top
Repair was easy once I got the correct part. When the parts were listed as small and medium large I thought they were talking the diameter of the bowl. It turns out they are talking about the center hole in the bowl. So I needed one small and three large. Everything great now.....stove looks great and clean.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Lorain, OH
- Parts Used:
- WB13K25
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
only back burnners lit
Rremoved the back cover, changed the wires from one ignighter to the other, removed the old ignighter, and snapped in the new one, put four screws back on cover, and pushed stove back into place, turned on all burners several times to make shure eveything worked!!!
Was this instruction helpful to you?
Thank you for voting!
change over from natural to lp gas
i removed the cover over hole that holds the orifice used a 7mm nut driver with butyl rubber tape stuffed inside nut driver, this stuff is sticky and holds orifice in place while positioning over hole.total time about 3 minutes. they worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Arlington, MA
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Left side front and back burner would not light
I located the spark module at back of top panel and I switched the wires of one of the other burners to the burner that wasn't lighting. By doing that I found that part of the module wasn't operating properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Las Vegas, NV
- Parts Used:
- WB13K25
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner Spark Module burned out needed a replacement
My husband did the repair so it was very easy for me, as well as for him, he found the bad part from your parts diagram which was a great help, he changed it out in no time and so we were both very Happy. Thank you for your help. Nancy & David
Was this instruction helpful to you?
Thank you for voting!