JEC9536BDS Jenn-Air Cooktop - Instructions

Removed cooktop, wiring and coil. Marked where wires went on limiter
tabs. Ordered coil 1200 Watt, received a 1500 one. Sent back to PS with prepaid shipping label {great}. New one had a different limiter tab arrangement. The instructions included warned this but doesn't tell you where to put the wiring. Instructions say to remove the old limiter and put it on the new coil but this can not be physically be done plus who would want an old limiter on a new coil.
Found a YOU TUBE video on how to test and place wires on limiter switches which shows the number letter sequence on the ceramic part. Maybe PS will put that info in their instructions. Coil works great !!

Access to burner nothing like on-line videos:

1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.

Went well. Husband, who has some appliance repair experience, did repair in less than a hour. Replacement burner was not an exact duplicate of original but he was able to adjust for that.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

I used the digital multimeter for measure the voltage in the burner and in the digital part,I saw the electric cables

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harness, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip your breaker. But now we have a range with 4 burner after a year THANKS

Disconnect the power.took the cooktop off the range. Turned it over. Removed the underside plate. Disconnected the bad element. Pluged inthe new element. Replaced the under plate. Reconnected the range to the stovetop .put cooktop in place. Reattached screws. Turned on power. Worked perfectly.

I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.

i did fine

Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turned the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

OMG you have no idea how grateful I am. My husband and I watched your how-to-video and decided that it looked pretty easy for us to replace on our own. We saved close to $200 between the flat fee for a service call plus labor. Thank you very much. We were also pleased how fast our part was shipped to us.

Shut off 220 volt power to range. Removed two screws for cooktop element access. Used needle-nose pliers to remove power (2) and control (2) lugs and wires. Remove defective cooking element module, replaced. Reverse steps for new unit.

I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.

Remove top oven door,remove two hex head screws located underneath cook top at the front on both sides,slid the range top forward approx. three(3) inches to obtain access needed to unplug the wiring harness, located behind the vertical part of the cook top,removed the cook top,placing it on a padded table with the glass side down,disconnected the three (3)wire spades and unscrewed three screws anchoring heating element to the cook top frame, replaced defective heating assembly with new. Repeated above steps noted above,in reverse order. And yes, all work was done after power was shut off at power panels dedicated oven circuit.