JGC9430BDR13 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Glenn S from Edgewater, FL
- Parts Used:
- 74007734
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electtrode
removed screws that hold burner in place lifted and removed wire connection, reversed attached wire replaced two screws job done,,,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PRATTVILLE, AL
- Parts Used:
- 74007734
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode not working.
Removed two screws and slipped the electrode connection off. Then reserved the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L from FAIR OAKS, CA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the gas burner head needed to be rerplaced due to the sparker not functioning properly
Ordered a replacement, removed the old burner and installed the new one. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan J, from UNIVERSAL CTY, TX
- Parts Used:
- 74007735
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Needed use of penetrate lubrication
Removed two screw securing wburner and disengage igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from EADS, TN
- Parts Used:
- 74007736
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!
Voila!
Was this instruction helpful to you?
Thank you for voting!
Igniter clicked but burner would not light
Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from neuvo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Rochester, NY
- Parts Used:
- WP74007749
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I lost the cap
after I received the cap in the mail, I removed the grillwork and set the cap in place. then replaced the grill and my wife fixed my supper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cresco, PA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range would not light.
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Overland Park, KS
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The ignitor went out on one of the burners of the gas range
Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from flushing, NY
- Parts Used:
- WPW10168628
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob melt do to heat
chang knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from flushing, NY
- Parts Used:
- WPW10168628
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burnt knob
changed knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hendersonville, NC
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor cracked and would not light
Simply removed the old ignitor and install the exact replacement part. Work great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ned from leland, MS
- Parts Used:
- WPW10475147
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
would not light
remove two screws then unplug the wires put the wires back on the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from La Habra, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
Was this instruction helpful to you?
Thank you for voting!