JGD3536BB00 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from FAYETTEVILLE, GA
- Parts Used:
- WP74009336
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Replaced electrode. Complications heat soldered set screw to electrode
Installation is simple and very straight forward. Problem, was i stripped the torx screw to release electrode because the screw was frozen. I then tore electrode out leaving space to use penetrating oil (inaffective ) then using a chisel to pop the screw out. It came out intact and did not damage the threads in the burner. So what could have been a 20 minutes job, turned into over an hour. But still worth doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from WOODLAND, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Replacing burner electrode
This should be a 5 min job. Lift off the burner cover, remove two screws to lift of the burner base and then remove a Phillips head screw that hold the burner igniter in place.
Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!
With no rust, this should be an easy 5 minute replacement. The burner now works great!!!
Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!
With no rust, this should be an easy 5 minute replacement. The burner now works great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CONCORD, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Weak spark for igniting gas burner.
Removed the gas deflector; unscrewed the burner body; pulled off the ignition wire; unscrewed the bad electrode; screwed in the replacement electrode; reversed the steps. Voila! Perfect operation once again. My one mistake? Ordered the wrong electrode initially. Make sure you get the right part the first time around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from san juan bautista, CA
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
erratic spark from electode,gas would no ignate.
Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sherman Oaks, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electronic ignitor malfunctioned
First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edgar from COCKEYSVILLE, MD
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor sparking at bottom, not the top
Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn S from Edgewater, FL
- Parts Used:
- 74007734
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electtrode
removed screws that hold burner in place lifted and removed wire connection, reversed attached wire replaced two screws job done,,,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan J, from UNIVERSAL CTY, TX
- Parts Used:
- 74007735
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Needed use of penetrate lubrication
Removed two screw securing wburner and disengage igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L from FAIR OAKS, CA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the gas burner head needed to be rerplaced due to the sparker not functioning properly
Ordered a replacement, removed the old burner and installed the new one. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Kansas City, MO
- Parts Used:
- WP7504P298-60, 74007734
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner failed to light.
Unscrewed the two star headed screws, disconnected the electrode, then replaced the electrode and reattached new burner with same screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PRATTVILLE, AL
- Parts Used:
- 74007734
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode not working.
Removed two screws and slipped the electrode connection off. Then reserved the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from EADS, TN
- Parts Used:
- 74007736
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!
Voila!
Was this instruction helpful to you?
Thank you for voting!
Igniter clicked but burner would not light
Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from neuvo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!