JGD8130ADW20 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Craig from Ashburn, GA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotten filter for down draft vent
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Annapolis, MD
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the grease filter!
Followed the directions. Piece of cake!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Flower Mound, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilber from oshkosh, WI
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
terminal spade wrong size on range wiring to fit module
cut off terminals and replaced with the right size one's stove lights every time now wlrowe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bronius from College Station, TX
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Intermittent but rare spark when I went to start the rage: spark module definitely was toast or on its way out
The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..
Anyhow, thanks to the great part, the stove works really well again.
Anyhow, thanks to the great part, the stove works really well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Ocala, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Holes in the air filter of our Jenn-Air grill
Simply pulled the old filter out and put the new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathryn from batavia, OH
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
fan switch blew fuse & burned wires to switch.
take off frt of stove around burner knobs, remove old switch, put on new, replace frt of stove. Fast, easy & look at your savings!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Block Island, RI
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken insulator for top burner igniter
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cor F. from Pasadena, TX
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Replacement of a Dead Spark Module
The spark module pulses a stepped up voltage to all four burner sparks at the same time regardless of which burner you want to ignite. I read that this part lasts about 10 years. I don't cook much and it lasted 13 years. On my Magic Chef the part is behind the right side wall panel. Lift the range top,remove all the screws that hold the right side panel in place. This replacement can done without opening any gas fittings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inga from Petaluma, CA
- Parts Used:
- WP74005890
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Only two burners lit
Removed old igniter set replaced with new one. Hardest part was using the screw driver to removing the backing. Saved us having to buy a new stove since we just bough the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from McMillan, MI
- Parts Used:
- WP3403M075-29
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner was burnt out
Replaced burner. Simple really. Fit perfectly and works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Holladay, UT
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June S from San Antonio, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was very old and falling apart.
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bam from Wilmington, NC
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
The high/low fan switch was inoperable.
The available replacement switch is a bit too large to fit into the hole on the original face plate which must be kept as it also mounts the 4 burner dials and the “on” light.
A local machine shop was able to make the original hole large enough to accommodate the new switch. Total time to detach and reassemble the original face plate, less than 2 hours. Other than the new switch being black, it looks original. (The 2 smaller face plates provided with the new switch were not needed.)
A local machine shop was able to make the original hole large enough to accommodate the new switch. Total time to detach and reassemble the original face plate, less than 2 hours. Other than the new switch being black, it looks original. (The 2 smaller face plates provided with the new switch were not needed.)
Was this instruction helpful to you?
Thank you for voting!