CVG4380PD Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Patricia from COLORADO SPGS, CO
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner would not light
Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Raleigh, NC
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
This item needed replacement for the 3rd time due to finish wearing off, within 6 months EACH time.
unscrewed previous unit, placed new unit and screwed in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from COLUMBUS, OH
- Parts Used:
- WP71001057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knob broke on range
Simply removed old knob and popped on new knob. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Baton Rouge, LA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old filter to replace
:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Portland, OR
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner inoperative
Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H from Newfoundland, PA
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Ports were worn and oversize
Removed the two screws that hold burners on mounting bracket . Removed burners and installed new burners. re-adjusted air flow to elimenate yellow flame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yong from Houston, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Palm Coast, FL
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
didn't ignite gas range.
After getting help from customer support, I was able to order the part. I tracked the part on FED EXp.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Poulsbo, WA
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
One 25 yr-old burner was beginning to leak gas because of corrossion. Decided to replace all 4 burners.
Remove grates and pan. unscrew each burner from the metal cross mount bar, keeping in mind, the position of the cross mount bar.(Mine was not reversible.) Reverse the procedure with the new burners.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)
Biggest problem was making sure the correct parts were ordered.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)
Biggest problem was making sure the correct parts were ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Whitefield, ME
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
tube was rusted out
just removed two screws - took old unit out - put new unit in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Bangor, MI
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Old burners were worn out and wouldn't light with the ignitor
Removed two screws and replaced burners and placed the unit back into position and the burners worked perfectly. Very easy. I think anyone could do this task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Shawano, WI
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob
Just had to push it into place, by hand only
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- darryl from everett, WA
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Gas Valve Knob for Jenn Aire Gas Stove
Slipped off old one and slipped on new one. The part was the right one and works great. Timely receival of part was great. Communication from you was great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Mcdonough, GA
- Parts Used:
- WP71001057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed the knob for stove
Put it on simply as that thanks it was a perfect fit!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martyn from Middletown, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this instruction helpful to you?
Thank you for voting!