JGC8536BDB10 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Lakeside, Arizona, AZ
- Parts Used:
- WP74009336, WP8273062
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Igniter did not work
Bought The burner with the electrode already installed. The only way to go, since the screws will not come out without breaking. Also purchased two torx screws as thay also broke. A bad design by the manafactor.Had to drill and tap out for new torx screws to fit into the gas houseing. PartSelect had all the parts I needed. Dan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Two Rivers, WI
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Igniter Needed Replacement
Removed the burner & igniter as a unit. Screws holding burner down were very tight. One came out with effort, the other one the head broke off. Tried heat but to no avail. The screw holding the igniter had to be drilled out. Fortunatly I work in a machine shop so I was able to remove the screw, but the hole was then too large for the replacement screw. I wound aluminum foil around a toothpick to form a bushing in the hole so the screw could grab. Same principle as those plastic anchors for plaster or drywall. Bought stainless screws, but did not even try to get the broken screw out of the cooktop. The one screw holds it in place just fine. Wife is very happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- grant from aurora, CO
- Parts Used:
- WP74009336
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Spark Ignitor replacement
Screws holding burner base and ignitor were plain steel. If they had been stainless they probably would not have rusted in so tight. One in the base broke off, and the one holding the ignitor could not be removed, even with heat from a torch. I ended drilling it out and re-tapping the hole. If I wasn't mechanically inclined I would have had to give up and order a new burner base.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sanbornton, NH
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Deer Park, IL
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Burner electrode was damaged during cleaning
A crack in the porcelain caused the spark to not go in the proper direction, therefore the burner would not ignite. To have the job done by a professional would have cost $200.00 plus parts. Remove two phillips screws lift the burner out then remove the one phillips screw that held the electrode. Then with the new electrode in place reverse the previous steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olympia, WA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
igniter would spark, but not light flame
Installed new igniter, but would still not light flame. Determined it was a design flaw. On our range, the 2 right hand burners have "lift-off tops" that are farther away vertically from the igniter than the smaller left hand burners. I placed asmall nut from a nut-bolt assembly on top of the igniter, and now the igniter sparks higher to the "lift-off top" and the flame ignites everytime. Without that added heigt, the igniter just sparks uselessly around the base of the burner. There should be a higher igniter designed for the higher distance between the igniter and that removable top. Good luck with your own modification.
Was this instruction helpful to you?
Thank you for voting!