CVE4180W Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
Burner was not working & needed new grease filter
Parts arrived very quickly & the installation was quick & easy. Will order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Atascadero, CA
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
center piece of the heating element broke off
so easy, just ordered the part, the part came and inserted the element into the stovetop
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LouAnn from Maquoketa, IA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8 inch element not heating in cooktop
I removed the old element. I then plugged the new element in place. Simple repair, no tools required. Turned the cooktop element on to test for proper functioning. It heated properly. Repair completed.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charlotte, NC
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Escalon, CA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old switch became brittle with age and broke. There were two plastic cylinders that held a spring loaded bearing to operate the contact point. It became brittle because of age and it broke.
I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Indianapolis, IN
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stove top burner would not heat
new element plugged into burner connection- an easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from GAITHERSBURG, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
burner control stopped functioning.
Replaced the control.
Was this instruction helpful to you?
Thank you for voting!
Drip pans were in need of replacement
No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Control switch would not operate
Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Ironton, OH
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defetive fan switch
throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Chehalis, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
Was this instruction helpful to you?
Thank you for voting!