JGD8348BDP Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from Vashon, WA
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wore out burner and igniter
New burner and igniter.....actually it was very easy to to fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June S from San Antonio, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was very old and falling apart.
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Osage Beach, MO
- Parts Used:
- WP74005890
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas burner would not light-had to use lighter
As described for the part. Easy repair. Easy to diagnose thanks to feedback from another customer of yours. Part was received super fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dayton, OH
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner grate pads worn off or missing
I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joellen from Castro Valley, CA
- Parts Used:
- WP3403M075-10, 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner head was rusted through
This is the second burner head I have replaced. It was easier than the first time but the burner head I received did not have the screw holes to reattach the gas tube to the burner head. I was able to drill my own without too much trouble using a standard bit and electric drill. I used the old burner head to determine what size drill bit to use. Even so, it was still an easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from bartlett, TN
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner head rusted out
undid about 7 screws to get access to underside of burner, unscrewed 4 screws that held on gas feed pipe and ignitor. twisted out old burner and gently removed ignitor from burner. cleanded up area where burner was and installed new one. took a little bit of tweeking to reinsert ignitor but did slide in nicely. reattached gas pipe and all screws. slide burner case back into position. turned on and worked nicely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Nashville, TN
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
gas burner had rusted out
replaced burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MADISON, FL
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burner Igniter And Burner
Dis mantel burner unit removed burner replaced burner and igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Syracuse, IN
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The old burner was rusted through and the gas port came loose from it.
To gain access to the burner, the bottom of the double burner unit had to be removed (7 screws). Once this was achieved, it was a simple matter of removing the old burner head which is captured with three lobes that engage the unit much like a thread,(which in my case was stuck in because of rust and had to be persuaded with a pipe wrench). The new burner was installed with hand pressure only, and once the gas flange was remounted and the ignitor hooked up, I just re-attached the bottom of the unit and viola!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inga from Petaluma, CA
- Parts Used:
- WP74005890
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Only two burners lit
Removed old igniter set replaced with new one. Hardest part was using the screw driver to removing the backing. Saved us having to buy a new stove since we just bough the house.
Was this instruction helpful to you?
Thank you for voting!