JED8130ADW Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martyn from Middletown, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LouAnn from Maquoketa, IA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
8 inch element not heating in cooktop
I removed the old element. I then plugged the new element in place. Simple repair, no tools required. Turned the cooktop element on to test for proper functioning. It heated properly. Repair completed.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Ordering the part was easy and it arrived within 2 days. Very happy with Parts Select service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Ironton, OH
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defetive fan switch
throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alene from INDIANAPOLIS, IN
- Parts Used:
- WP660532
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners needed replacing
Pulled out the old burners and put in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Escalon, CA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old switch became brittle with age and broke. There were two plastic cylinders that held a spring loaded bearing to operate the contact point. It became brittle because of age and it broke.
I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Alexandria, VA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Indianapolis, IN
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stove top burner would not heat
new element plugged into burner connection- an easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Oceanside, CA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pittsburgh, PA
- Parts Used:
- WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
element shorted out
Replaced the element. The part came the next day which was great. Good customer service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Buford, GA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fan Switch Broken and being held only by Electrical Wire Connections
removed two screws under fan cover at end of stove knobs. raised panel with knobs up and removed two nuts that held fan switch housing. installed new switch and moved power connections to new fan. (note: Killed power to range top prior to any repair action)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Moultrie, GA
- Parts Used:
- W10341820
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Goshen, NY
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter couldn't be cleaned
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from St Louis, MO
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan & stove did not operate.
1st removed 2 screws & removed 2 leads ( then the fireworks started/ did not know the power was still in the leads), so removed the power. On the net picked a fan sw. from a picture & ordered it. The service was swift but the part was wrong ( had 3 contacts rather than 2/ I thought by this time they made one sw. for 2 purposes) WRONG.I called in to explain my problem & Susan M. helped me with the right part & excellant service. Thank you Susan.
Was this instruction helpful to you?
Thank you for voting!