22114 Jenn-Air Cooktop - Instructions

The burned control switch was not functioning. It took a while to find the range model number and then the part number of the switch. It was cool that I could see a picture of the part with the part number on the internet so that I was sure to buy the right part.
Once the part arrived, I turned off the power to the range (circuit breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available

removed all for knobs and replced with new ones

I pulled off the other 3 old knobs. Pushed on the new ones, which pushed on hard, but work. They stick out farther than the originals. They look a little different, but only to me. No one else would notice.
The main part is, it works. A little spenty for my taste, but did not know where else to go and they arrived very quick.

our cook top is so old, but no need to replace just yet. so I ordered new knobs to get a new look
thank you!

SHUT OFF BREAKER! Remove exhaust grill and switch knob. Remove cooktop switch panel by removing two screws and sliding panel toward exhaust grill. Remove switch retainer nut with deep socket. Transfer wires one by one to new switch. Install new switch tightening retainer nut. Reinstall switch panel with two screws, push knob onto shaft. Turn on breaker.

Just slip new knobs on. Simple and works great!!

I am not really handy. When the repair man came and gave me a price of $220 to repair two infinite switches, I looked up the cost of the switch and saw that it was easy to do...and it was! I saved $140 for doing it myself (no help from my husband).

First I turned off the power, unscrewed two screws and took the knob panel off. Wrote down the colored wires and then pulled them off the infinite switch (some needed pliers) and then i just put the wires back on the new switch...done...it works!

Your staff helped me find the updated replacement that worked and when I was having some connection issues helped me get it right!

Important: 1) ALWAYS REMOVE ALL POWER FROM THE STOVE. 2) Do not "preassemble" the ceramic recepticle and wire kit. The wires are nearly impossible to remove from the receptacle once inserted. The wire colors have changed and are not the same color as your old wiring. 3) All the fasteners are sheet metal screws, different sizes (note where they are used) and are easly stripped if tighted too hard. Either unplug the stove or open the main circuit breaker to the stove. Take out the right-hand burner cartridge and place it aside. remove the center screw and metal strip from the old receptacle (you will reuse this item). Loosen the control panel from the front of the stove by opening the oven door and remove the four screws holding the control panel in place (Screws are located on the underside of the control panel). The panel slides down about 1/4 inch and tilts forward exposing all the control wiring. Ues a hex-headed driver or large screw driver and remove the drain plug from the drain pan. Use care as there is a small gasket under the drain plug. Remove the four screws holding the burner's pan to the stainless steel stove top. Move the wire bundles aside and GENTLY pull the burner pan half-way out of the stove (it is a tight fit but do not use force. Remove the screws and strap holding the old receptacle from the pan. Withdraw the pan from the stove. (good time to clean the pan and drain plug) With the old receptacle now exposed, assemple the new receptacle and wire harness wire for wire carfully replacing each lead. The new wire harness is inserted into the new receptacle thru the top of the receptacle and will lock in place within the new receptacle. The blades on the end of the wires must point toward the slots in the receptacle. The receptacle wires will be pointing down. Trace each wire and be certain the correct wire is switched out with the proper lug on the control knobs within the stove (needle nose plyers will help but do not force the connections). Gently push the pan halfway back into the stove and attach the new receptacle to the pan with the small metal strap across the back of the receptacle with screws. Push the pan all the way back into the stove and re-attach the pan to the underside of the stove top with sheet metal screws. Re-install the drain plug and drain tube. Tilt the control panel, slide the panel back up into the front of the stove and reattach the control panel with sheet metal screws. Re-install the small metal clip into the front of the receptacle (one end of the clip slides under the stove's stainless top frame). Reenergize. Reset the clock. You're done.

Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.

Hubby & I

Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY

removeed the dial cover, paced the lens into the hole, slid the light and holder into place , 5 min job.

Easily removed the old knobs and applied the new ones.

replaced old worn silver and white control knobs with new black ones.