JEC8430ADN Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sergio from JENSEN BEACH, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner did not heat up
Access to burner nothing like on-line videos:
1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.
1) Remove 4 screws under front control panel. (Oven door needs to be open.)
2) Remove 2 flat head screws on sides of control panel. This will loosen control panel. Capture control panel to keep from hanging from wires/connectors. I used hooks made from a wire hanger.
3) Remove 2 screws to remove two steel panels on either side of stove.
4) Remove rear screw of the 2 front screws now exposed and 2 rear screws near top of stove.
5) Carefully flip over glass top being careful not to pull on the wires.
6) Identify burner to be replaced. Note 2 numbers where two clamps are attached to burner.
7) Using 3/8” nut driver, remove screws to allow removal of burner. Remove wires per included instructions. Remove burner.
8) Place new burner under clamps and align to the holes by the two numbers noted in step 6 above.
9) Connect wires to new burner as per included instructions.
10) Reverse removal steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REX from VIRGINIA BEACH, VA
- Parts Used:
- W10823704
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Small burner on glass top stove stopped working.
First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Gloucester, MA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Brocken Burner Knob
This was a simple replacement of a burner knob. The website had exactly what I needed, including a photograph so I was sure it was the exact match. Delivered quickly and was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo from Lenexa, KS
- Parts Used:
- W10823698
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
the burner didn't work and digital part too
I used the digital multimeter for measure the voltage in the burner and in the digital part,I saw the electric cables
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mary Esther, FL
- Parts Used:
- W10823704
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
element or temperature sensor failed: not working
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Qiong from Mckinney, TX
- Parts Used:
- W10823694
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
outer ring of dual radiant burner doesn't work
Thanks for the previous viewer's tip, disconnect power, pushed the cook top out of the counter and used a wood block for the support. Unscrew the smooth top from the burner, remove old and plug in the new one. Connect power, test OK. Put everything back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Half Moon Bay, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A plastic handle cracked and was loose.
I lifted off the broken handle and replaced it with a new handle. It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Wilmington, MA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knob was cracked where it meets the shaft
Took broken knob off and slid the new one on. DONE!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delton from Nevada, MO
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken burner knobs
So simple -- any monkey could do it. Pull off the old knobs and push on the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Charlotte, NC
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs split and will not turn on burners
Removed old knobs and replaced with new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Boca Raton, FL
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken knob to stove top.broken by me
First went to an appliance distrib. store.They would have to part.Was qouted a price.Wenthome and went online to partselect.com and saved 40% even with shipping.Got the part the next day!Pulled old knob off and pushed new knob on.Thank you for making it easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ginger from Hickory, NC
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knobs
We have had this appliance for 18 months. Within one month the first knob broke. A month later, the second knob broke. We have gently been using the remaining 2 knobs for 4 burner positions until recently when the other 2 broke. I am hoping these new knobs are made better then those that came with the appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Davis, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had a broken air vent knob on my range top.
The part was here three days after ordering and I put it on with no tools in less than a minure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marv from Bella Vista, AR
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knob got stripped out, taking them off and on...
Got on line and ordered part and lined up flat side of inside of knob and slid it on... That simple... The person who put them on after cleaning stove never knew there was a flat side inside knob.. We never stop learning, do we???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kim from Pahrump, NV
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
previous owner broke knobs by not pushing down to turn on, then leaving the D rings on when they switched them. Only 1 burner was operating
I carefully pulled the 3 D rings that were left on the posts of the burner controllers with a pair of needle nosed pliers, made sure there was nothing on the controller posts, then put the new knobs on. Make sure there are no D rings on the oven knob posts, 2 of the knobs were fine, they just didn't have D rings in them. Partselect was great. Items were received within 2 days. I would definately recommend them.
Was this instruction helpful to you?
Thank you for voting!