C316W-C Jenn-Air Cooktop - Instructions

very easy - not really a "repair" more of a face lift, although the grill was unusable.

Parts were perfect - Used it the same night.

Remove cover plate, install new switch, replace cover place. Replace one wire at a time, a pair of needle nose pliers may be helpful. Surprise of this job was that I had a torque screw driver (I think that's what it's called) to remove the switch from the cover plate. These are the screws you'll see after removing the knob. Find that driver before you begin, mine was in the garage and for the life of me, I can't remember why I ever had one in the first place.
Thanks for a great web site!

replaced stove top switch

Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.

Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!

Really easy ...followed advice posted from others with same problem. Before anything disconnect the power at the breakers and use a voltage detector to verify there is NO POWER!!!! Only need to remove the two phillips screws on the four controller panel, Slide panel away from you to access the controllers. Match wire/connector for connector from the old to new controller. Reassemble, restore power .. Happy wife!!!. She has been on my case to fix this thing for several years.

I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything worked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.

Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions

1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release top edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.

I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.

Removed top and front panel

The repair is very easy. Part Select is awesome as far as getting you to the right parts. Just remember that when you do a repair with electricity that you take the time to shut off all possible power sources. I did not and got lucky that I did not injure myself because I did not know the fan switch was also bad. This caused a direct contact with a metal part on the control switch housing while I was disassembling the stove top control. Take your time and think. Should have no problems. Norbert.

1. Flipped breaker and confirmed no power at cooktop.
2. Removed the Fan grille and removed the two screws holding on the control panel. It tilts up and out to the rear.
3. Unscrewed the 2 screws on top holding old switch to panel.
4. Disconnected the wiring one lead at a time and connected it to the new switch in the same spot. There are 5 wires total and I carefully used needle nose pliers to remove reluctant wires and to adjust connectors if they were loose on new switch
5. Screwed the new switch onto the panel and screwed the panel back onto the cooktop.
6. Tested new switch...worked great.

Turn off power at breaker
Turn off water supply
Remove 2 screws at baseboard plate
Remove 2 mounting screws attaching machine to floor
Open door, remove 2 mounting screws attaching machine to bottom of counter
Disconnected water line
Carefully pulled machine out about 8 inches to expose broken spring
Attached new spring using directions included with package from PartSelect
Reassembled in reverse order
Check for water leak before attaching baseboard plate

Took the door apart and replaced the hinge, very easy