JED8430ADW Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Walla Walla, WA
- Parts Used:
- WP7739P121-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken knob
used pliers to remove broken knob and push new one on with my hand
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from AIKEN, SC
- Parts Used:
- W10823704
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Element burn out. Would not heat
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Seth from Old Orchard Beach, ME
- Parts Used:
- W10823704
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced Burned-out Cooktop Element
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included extension wire for one that would not reach with the new configuration and everything works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elsie from OLATHE, KS
- Parts Used:
- WPY706012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter was falling apart
Just placed new filter in slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Duarte, CA
- Parts Used:
- W10355051
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cleaner
just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vickie S. from Wolfe City, TX
- Parts Used:
- WP74009593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The burner knobs were broken or burned.
Removed the old knob and put the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Mary Esther, FL
- Parts Used:
- W10823704
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
element or temperature sensor failed: not working
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from High Springs, FL
- Parts Used:
- 12002125
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
control failed
Couldn't hook up the wires since the instructions were so cryptic. Ended up fixing old control and re-installed it. Worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberto from Zapata, TX
- Parts Used:
- 71003476
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Fan not working
Opened the top section of the stove. Re-routed wires to be connected from the speed control device into the new cord. And done. Put everything back thogether.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sue from Lakeway, TX
- Parts Used:
- WP74009593
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I very stupidly set a very hot pan down on a couple of plastic knobs and it melted them.
I set the new knobs down on the spindle that holds them and snapped them into place--a matter of two minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Leesburg, VA
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace old grease filter
very easy slip in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Cottontown, TN
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Nasty, clogged, old grease filter
I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Hot Springs Village, AR
- Parts Used:
- W10823704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
surface burner failure
Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dewey from Wilson, NC
- Parts Used:
- WP74009254
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan Control Switch stopped working
Looked up the part on the internet. Found it with ease. The thing I did miss was that the switch had a small nub to keep it in the right place in the Glass top. The repair went easy. Probably took no more than 15 minutes. I would use PartSelect again.
Was this instruction helpful to you?
Thank you for voting!