C301 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Val from Suwanee, GA
- Parts Used:
- 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The knobs were stripped and we could not turn 2 of the burners on.
I used pliers to remove old knobs and just inserted the new ones. I had tried using cheap generic knobs that did not work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- catherine from holland, MA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knobs were old could not read numbers
knobs fit perfectly
Was this instruction helpful to you?
Thank you for voting!
Infinite Switch failed, burner would not heat
Removed two screws holding 4-switch panel, drew a simple diagram to assure placement of wires on correct terminals, removed and replaced switch.
Switch works fine, but original knob does not fit shaft of replacement switch. Will try to order new knob, but it probably won't match the old knobs, so range will have one new knob & three old ones. I wish the order page noted that new knobs must be ordered to fit the new style shaft.
Switch works fine, but original knob does not fit shaft of replacement switch. Will try to order new knob, but it probably won't match the old knobs, so range will have one new knob & three old ones. I wish the order page noted that new knobs must be ordered to fit the new style shaft.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Williamsbirg, VA
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
All four of the cooktop switch controls needed replacing since none would control their respective burner.
Turned off the power at the circuit breaker panel. Removed the control knobs from each switch and the four palnuts under each knob. Removed the two screws inside the vent well that hold the escutcheon in place. Pulled each switch up as much as possible to expose the wires attached underneath to each switch blade. Remoced each wire and replaced them on the new switch. Same procedure for all four switches. Reassembled in reverse order. Turned on power and all four burners lit up and were regulated as if new. I saved $244.00 doing the repair myself.
Was this instruction helpful to you?
Thank you for voting!
Switches were worn out (2) and shorting out. Throwing the breaker. Actually I think the ladies boyfriend/ fiance' tried to replace the knobs that were broken with universal knobs. They didn't fit so he forced them and broke the switches internally.
Shut off the breaker! Removed down draft grill. Removed two phillips head screws and lifited switch plate out. Removed switches (2) and made wiring diagram as I went. Looked up Jenn-Air on line and ordered parts. Lost wirihng diagram in the process but still had two switches wired . Replaced all four switches. Everything working great. However while I was waiting on switches to arrive, somebody at the house was fooling with the switch plate and broke the on red indicater lens so now I'm ordering that. Oh well....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Frederick, MD
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the element plugged in, stove was woking right away.
The element plugged in to the cook- top.The cook -top was working moments after i unpacked the element. thank you.
Jim B.
Jim B.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from ESTERO, FL
- Parts Used:
- WP5700M611-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
drain jar lids rusted and broken of their mounts
The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Carson City, NV
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The 8" burner switch would operate both the 6" and 8" burner.
First pulled the two screws holding the control with the switches. Then I unscrewed the nut holding the 6" burner switch and disconnected the wires on the switch and replaced the switch with the new one. Replaced the control unit in the range top and tested the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Chandler, TX
- Parts Used:
- WPY707985, 715957K, WP71003558
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
high blower vibration
blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from LAKE GROVE, NY
- Parts Used:
- WP71003558, WP707929, 715957K
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
Downdraft Motor Bearings Shot
I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Palo Alto, CA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burner temperature control did not work.
Got a no-name tailor-it-yourself replacement switch from a San Jose, CA appliance parts store; but the switch was so cheaply made that it fell apart when I tested it.
Got a RobertShaw part from PartSelect and now the burner works perfectly.
Got a RobertShaw part from PartSelect and now the burner works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Galveston, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Reusable Grease filter was old and worn out.
The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nora from AUBURN, WA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The switch needed to be replaced
I TURNED OFF THE POWER TO THE GRILL FIRST. Then Removed the knob on the top face plate and then removed the 2 self tapping screws at the high end and this allowed the face plate to be pushed forward. And allowed access to remove the switch I removed the wires one at a time and replaced them on the new switch. All done in 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina C from Oakland, MD
- Parts Used:
- 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I broke my knobs off with cast iron skillet, old knobs needed replaced.
I removed the old knobs and replaced with the new ones. We also replaced one of the switches which the knobs fit on, because I broke the switch off with a Cast iron skillet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from Bristol, RI
- Parts Used:
- 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old
I lifted off the old knobs, pushed on the new. Easy and the cooktop looks brand new!
Was this instruction helpful to you?
Thank you for voting!