CVE4270B-C Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Diane from Flower Mound, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Annapolis, MD
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the grease filter!
Followed the directions. Piece of cake!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Ashburn, GA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotten filter for down draft vent
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vanna from St. Johnsbury, VT
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front right burner did not turn on
We followed the instructions on the video after receiving our part - they were perfect instructions and led us right through the repair. I have to say it would have been harder to do with one person - but probably doable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vernon from Evergreen, CO
- Parts Used:
- 71001578
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
fan motor seized
Replaced motor. 2 screws, 5 wires, 8 nuts, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Collegeville, PA
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner only operated on high, no medium or low heat.
First I moved the left rear burner to the right front. No change. Then I moved the burner units from left to right, No change. I guessed it was the control switch and ordered from PartSelect. Turnaround time from PartSelect was excellent.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
I turned off the powerr to the range. Removed the screws holding on the front panel and then pulled the panel out far enough to see behind it. I located the faulty control switch and then held the new switch, next to it, and turning to proper orientation. I then, one at a time moved the wires to the new switch. After that it was mount the new switch, put the panel back in place and turn on the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Sherman, TX
- Parts Used:
- WP7518P054-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
a few months ago, my daughter-n-law and I were hitting up tacos on the grill----the grates melted ---I thought I would have to purchase all of the parts even though only the grates were ruined---I am very pleased with my find with you.
just laid them down on top of burner and coals,----easiest installation ever----We are already grilling ----this is just like grilling outside but in AC
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharyl K from Nampa, ID
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Left Rear Burner would not work
Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- felton from sunset, LA
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Fan Switch burned out on Jenn-Air stovetop
The original fan switch for down draft stove top was discontinued! I found a replacement switch which worked just fine! I received switch and 2 different type replacement plates! One an exact match! Switch different but worked fine! I had to make no modification! Changed I'm about 10 minutes! I was lucky from what I read on other customers' responses!! They wouldn't promise me it would work!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June S from San Antonio, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was very old and falling apart.
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from snellville, GA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner stays hot
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Temple Terrace, FL
- Parts Used:
- 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heat Errosion
Wife installed them, they just snap into place on the Rock Grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Woodland Park, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner was very hot regardless of setting
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Port aransas, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rear Burner Was Not Functioning
Used a multimeter to determine that power was going to the surface burner infinite switch. Then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to torx head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed torx screws in the new switch and installed all screws back into range top. Reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Clive, IA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Dropped cast iron pot broke switch shaft off
The video you provided was excellent! Turned the circuit breaker off. Removed four screws, pulled out control panel, took a picture of the wiring to be safe. Disconnected the wires from the damaged control and removed it (two screws removed). Mounted the new control, connected the wiring, replaced the control panel and the four screws. Circuit breaker back on, turn burner on. That's it. Thanks for the video!
Was this instruction helpful to you?
Thank you for voting!