CVE4180B Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Lafayette, LA
- Parts Used:
- 74011338, WP7518P054-60, 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn out / burned grill and components
very easy - not really a "repair" more of a face lift, although the grill was unusable.
Parts were perfect - Used it the same night.
Parts were perfect - Used it the same night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MYRTLE from GRETNA, LA
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stove top burner
perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Mountain Iron, MN
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter had hole wore through
Pulled the old one out & inserted the new one. Less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Valley Grande, AL
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
back burn would turn high no mater where you set the control knob.
Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I figure I saved about 100.00 dollers plus I learned something.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Moultrie, GA
- Parts Used:
- W10341820
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from CARROLLTON, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
could not adj. temp. stayed high all the time
replaced stove top switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gilbert from san antonio, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
grill was getting red hot with out control
Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Bourbon, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sparks shot out from under knob, then, no surprise, the burner didn't work
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Goshen, NY
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter couldn't be cleaned
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from St Louis, MO
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan & stove did not operate.
1st removed 2 screws & removed 2 leads ( then the fireworks started/ did not know the power was still in the leads), so removed the power. On the net picked a fan sw. from a picture & ordered it. The service was swift but the part was wrong ( had 3 contacts rather than 2/ I thought by this time they made one sw. for 2 purposes) WRONG.I called in to explain my problem & Susan M. helped me with the right part & excellant service. Thank you Susan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joyce from sequim, WA
- Parts Used:
- 715877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner drip bowl was too soiled to clean
couldn't find replacement in our town, which is quite
small and no Maytag dealers. So, I ordered on line two drip bowls and saved one"just in case"
Mission accomplished. Thanks allot.
small and no Maytag dealers. So, I ordered on line two drip bowls and saved one"just in case"
Mission accomplished. Thanks allot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Rancho Santa Fe, CA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter was torn and bent
I just lifted out old filter, and put in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bowie, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
One burner only heated to a high temperature.
I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from harlingen, TX
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
no heat to burner
Removed top and front panel
Was this instruction helpful to you?
Thank you for voting!