CVE4180B Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Hazel Green, AL
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bad fan switch
Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Sedro-Woolley, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Lefrt Front Burner Quit Working
Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yong from Houston, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from Fayetteville, NC
- Parts Used:
- WPY04100166, WPY04100165, 715878, 715877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old stove drip bowls needed replacing
Removed heating elements and dropped new drip bowls in and replaced new elements
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Boone, IA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
replace fan switch
remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.
Then place it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Starla from Tomball, TX
- Parts Used:
- WPY04100166, WPY04100165
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement of elements
Simply unplugged the old elements and inserted the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Dunnellon, FL
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The 6in burner would go to max heat regardless of the setting.
Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above
fine.Of course I did shut off the power before starting any of the above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ARCADIA, FL
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Falls City, NE
- Parts Used:
- WPY04100166
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
old burners, burning very uneven!
Pulled out the old, plugged in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from Alpharetta, GA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
fan switch pushed through, plastic housing broken
Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.
Was this instruction helpful to you?
Thank you for voting!
burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.
dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Chehalis, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
Was this instruction helpful to you?
Thank you for voting!
Burner was not working & needed new grease filter
Parts arrived very quickly & the installation was quick & easy. Will order again.
Was this instruction helpful to you?
Thank you for voting!