C202-C Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner was not heating
Took everything apart and replace the new parts but what I really want to share is the prompt shipment of my parts, I'm very satisfied and I will recommend the web site (THANK YOU)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from Hillsboro, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Electrical receptacle for burner was defective.
After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.
Was this instruction helpful to you?
Thank you for voting!
Screws holding recepticles in place had to be drilled out.
Removed screws by drilling one and using a pliers to remove 2nd one. At first did not have enough wire to pull recepticles out until I relized wires were clipped to back of range to hold in place. Unclipped wires, pulled recepticles out, cut wires and attached new recepticles by connecting wires with wire nuts (I think wire nuts were to small so I used my own a size larger). Another problem that I found was that the recepticles on my range were held in place only by the screws that attached the recepticles to the drip pan flang. I had to bend an L bracket to prop under each recepticle to hold the back of it up so the burner element would sit level over the drip pan.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from McALESTER, OK
- Parts Used:
- WPY700631
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
age & solivents melted the on pilot light lens
removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Manchester, MD
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Sockets for the burner elementss were burned out
I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Young from Cordova, TN
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
one of wire melted and broken off from receptacle
Cut broken wire and existed wire off and put splice on both new and old wires to connect them.
It's easy job.
It's easy job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Alpine, CA
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Wife left burner on
Replaced switch.
Was this instruction helpful to you?
Thank you for voting!
burner connecters lost contact
pulled he cooktop, replaced the recepticles, reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Ashburn, GA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotten filter for down draft vent
How I did the repair is no consequence. The service of easily finding the part on your site is GREAT! and the shipping time more than reasonable! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colette from Annapolis, MD
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the grease filter!
Followed the directions. Piece of cake!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Salisbury, NC
- Parts Used:
- WP7772P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The paint begin popping of my original grill. My son had a friend that said that he could remove the old paint and repaint for me. Unfortunately in the shuffle of a motorcycle performance shop the grill was lost. I have been trying to get help from Jenn-Aire since March and they just kept saying th
Very simple for me!!! Open the box, uncover the new grill and lay it in its place.
Thank you so much!
Thank you so much!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Flower Mound, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Willow Grove, PA
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
burner switch would only stay on hi
Replaced the switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Irvington, NY
- Parts Used:
- WP7772P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The paint had chipped and peeled on the inlet grill
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martien from williamstown, MA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
one pole of the socket corroded to nothing
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!