CG200 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- venugopal from edison, NJ
- Parts Used:
- 12001129
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Switch was broken
If you are buying online, i'm sure you know to remove atleast 2 screws! and fit them back. It’s very easy to fix it. Only thing that took time out of the 15 minutes is to push the metallic push nuts! But it was interesting to do that. Partsselect.com is really a good site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Silver Spring, MD
- Parts Used:
- WP705105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
to convert a cook-top stove with 2 burners and a side grill into a 4 burner stove.
Replacing the side grill burners was easy--lift off the grill covers and pull out the grill burners. Next, attach the new front and rear burners to the burner plate with 2 screws (the older version uses 4 screws) using a nutdriver. Place the 2 burner unit (now joined) into the 2 gas inlets (no screws necessary--just slip them over the tubes). Insert the grill pan over the burners and place the 2 burner grates over each burner. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernard from Las Vegas, NV
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fan switch broken
No problem, except the holes in the clips to hold the switch in were so small that the clips would not go over the pegs.
The solution - use supper glue.
The solution - use supper glue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Raleigh, NC
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
This item needed replacement for the 3rd time due to finish wearing off, within 6 months EACH time.
unscrewed previous unit, placed new unit and screwed in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BOLIVAR, TN
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Front burner wouldn't light because hole burned in metal tube that channelled gas to burner
So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from COLORADO SPGS, CO
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner would not light
Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Preben from Fox River Grove, IL
- Parts Used:
- WPY704513
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The stovetop gas regulator kept clicking in off position.
The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burma from Section, AL
- Parts Used:
- 3401X055-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The painted finish on the pan for my range started flaking.
Called Parts select and they replaced it in two days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Pittsboro, NC
- Parts Used:
- WP71001641
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The new Maytag knobs did not depress the half-round metal post and therefore did not allow the knobs to turn.
Inside the knob, I placed a dab of CA glue on the small plastic projection , which was designed to press against the metal post, but was just shy of it. By thus building it up the knobs function perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H from Newfoundland, PA
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Ports were worn and oversize
Removed the two screws that hold burners on mounting bracket . Removed burners and installed new burners. re-adjusted air flow to elimenate yellow flame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Port Republic, VA
- Parts Used:
- 12001129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
installed new fan switch for counter stove top
The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jules from St Louis, MO
- Parts Used:
- 12001129
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Fan switch was shot
Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josee from San Antonio, TX
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan was not working.
Took less than 15 mins to remove the old switch and replace for the new one.
Works like new!
Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raul from Tampa, FL
- Parts Used:
- 12200030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace old parts
Nothing really. Only couple of screws to attach the bracket holding the front and back burners.
The other parts: filter, burner, pan, where just replaced.
The other parts: filter, burner, pan, where just replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Portland, OR
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner inoperative
Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
Was this instruction helpful to you?
Thank you for voting!