CCG406B Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Chipley, FL
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
only one burner on the cooktop worked
Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Egg Harbor, WI
- Parts Used:
- WP71001641
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One burner knob melted and one had a broken "stem"
Pop off the old and on with the new. Took longer to open the plastic packaging each came in than to remove & replace old knob with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from Carlstadt, NJ
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replacing old parts
wanted a fresh clean look on the burners since they were old and getting dirty and blackened from use. Easy to replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Cambria, CA
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Range burner melted plastic jar and became clogged
Found the part number on an old box, ordered the part and it arrived next day. Installed easily and is working perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Mansfield, TX
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burners would not light - rusted
New front burners fit well, but back ones had just enough variance in tne angle of the gas-supply tube that it would not fit the mounting bracket holding both burners in place. I had to grind a small flange off of the bracket so the gas tube would clear. Once that was done the burners worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Columbus, GA
- Parts Used:
- 1430322
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Front burners would not light.
First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary T from Glenoma, WA
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Jenn Air oven door would not stay closed all the way so the light stayed on.
Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kris from Murfreesboro, TN
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven door didn't shut completely
We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from La Porte, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
broken hinge
Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kit from Temple, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The hinge broke and the oven would not close
We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Brecksville, OH
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
2 broken oven door springs
I watched the youtube video that was provided by this website on my computer while doing this repair step by step. It was a snap!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Omaha, NE
- Parts Used:
- 12200030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out burner grates
Lift and replace. This was the only web site that gave a picture with the correct size of the grates I was looking for. All the other sites gave approximate sizes and universal part numbers instead of the vendor part number. That is why I bought it here. I didn't want to have to return the product because it was off just a bit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Tucson, AZ
- Parts Used:
- WP71001641
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner knobs were melted beyond repair.
Replaced the old knobs with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Scott, AR
- Parts Used:
- WP3801F403-80, 3401X055-09, Y704518, WP705105, 12200030, WP90767
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replace Grill Side with Burners because I never used the Grill
Very simple remove the Grill section and install the Burners no reworking of existing Unit is required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BOB from hartford, KY
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
old burners wouldn't light
took old burners out, installed new ones . I was very easy and if i could do it anyone can. I used a rachet and thats the only tool i needed
Was this instruction helpful to you?
Thank you for voting!