CG206S Jenn-Air Cooktop - Instructions

No problem, except the holes in the clips to hold the switch in were so small that the clips would not go over the pegs.
The solution - use supper glue.

If you are buying online, i'm sure you know to remove atleast 2 screws! and fit them back. It’s very easy to fix it. Only thing that took time out of the 15 minutes is to push the metallic push nuts! But it was interesting to do that. Partsselect.com is really a good site

Turn off the gas supply and unplug the electric supply. Remove the top grates and the burner cartridges. Remove 12 screws around the top cover and loosen the two screws for the fan switch. Pull the fan switch up and out of the way, remove the top cover. With a marking pen, label the four igniter switches and pull them off the gas valves. From underneath, remove the gas line from the pressure regulator, then remove the regulator from the pipe coming from the circular manifold. With a 3/16 socket (1/4 inch drive) or a 3/16 nut driver, remove the four screws that hold the manifold. Then from the top pull the manifold up and out. On the bottom, remove the screw (1/4 inch socket or nut driver) and remove the old gas valve. That's it. Now just put it all back together in reverse order. I used pipe joint compound on the pipe threads. Check for leaks with a soapy water solution. If I had to do this again, it would only take me half the time. I wasn't sure how everything came apart the first time..

Inside the knob, I placed a dab of CA glue on the small plastic projection , which was designed to press against the metal post, but was just shy of it. By thus building it up the knobs function perfectly.

The only problem was the little push nuts that came with the new part were too small for the posts on the stove top. I had to go to hardware and buy some for about 10 cents that fit. Other than that, everything was great. Great service from this company!

Easily removed the switch housing. After that, the other experiences really helped me as the retainer rings on the old switch would not come off and I broke one of the threaded posts about a eight of an inch from the base. I pried the other one off, more carefully, with a screw driver and a vice grip pliers . I was already to use the "super glue" solution when I luckily found an old nut that fit the one remaining threaded post.

The spare part came within two days after I place the order on line. I drew a simple wire diagram of the faulty switch-regulator. Shut off the power to the stovetop, before removing the four terminals on the faulty switch-regulator. I pushed the old regulator up from the center pin and replaced it with the new regulator. The next step was to reinstall the four wire terminals using my wire diagram. Final step was to turn the power back to the stovetop and test the new switch-regulator.

Nothing really. Only couple of screws to attach the bracket holding the front and back burners.
The other parts: filter, burner, pan, where just replaced.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

Called Parts select and they replaced it in two days.

Took less than 15 mins to remove the old switch and replace for the new one.
Works like new!

Disable cicuit! remove 2 screws on control housing, lift housing. Remove retaining washers from mounting posts (a trifle difficult, but drill into them with an 1/8" bit...they'll break off enough to grab with needlenose pliers). Mount & wire new switch. The replacement retaining washers are too small...hold them in visegrips & ream the hole with a larger drill bit. Place washer in a magnetic hex drive bit, align over post & tap with hammer to start them, then use a small socket to tap them home. Screw down control housing. Enable circuit...voila!

Easily removed the housing - difficult part was removing old fasteners from posts - took 20 minutes caerfully using knive, needle nose pliers, screw driver. Used old fasteners - new ones provided were too small for posts.

My son did the repair for me. It was easy, he said. just slid it out and put new one in.

Broke both crimp on washers. Drilled two appropriate holes in a dowell rod, used these holes to hold the new crimp on washers. Then drove the washers onto the switch's built in pegs.