JED7430AAB Jenn-Air Cooktop - Instructions

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.

turned off main ckt breaker, then removed the two leads to the burner unit at the Infinite Switch; set meter to ohms and read 20 ohms. then checked the right hand burner leads, got same reading of 20 ohms. I decided then that the infinite switch was faulty. I then made sure all wiring was in the clear and turned the ckt. breaker back on and CAREFULLY read the voltage at the Infinite-Switch terminals to the burner. No voltage (0). Ordered the part and the grill now works fine. A few words about the assembly/dissasembly: The phillips screws holding the top cover were a bit rusty, as this grill is on our pool deck. When I replaced them i put a bit of high-temp silicone grease in the threads. this grease is used for auto brake service so the grill heat should not affect it. the only difficulty I had on re-assembly was lining up the top cover with the bottom pan to insert the screws.

To replace the knobs was easy simply pulling the old knobs of and pushing the new knobs on. Replacing the on off lites was a little harder. i had to remove the control box that the knobs were mounted on. follow the wires.One lite for the left side and one lite for the right side. The left side lite was hooked to the two left side controls and the right side lite hooked to the two right side conrols.The wires then went down under the unit to the electrical junction box and wire nutted to the main wires servicing the range. What I didn't realize is that the left front contrlo knob is the only one that controls the fan.It has fan onthe knob. the rest of the knobs are not to have fane on them.I didn't notice this when I made out the order now I have all four knobs that have fan on them.

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete

very easy - not really a "repair" more of a face lift, although the grill was unusable.

Parts were perfect - Used it the same night.

old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Not much to tell about installing a new grill grate.
Partselct.com was very prompt and efficient in sending out the part.

Removed old filter, dropped in the new one.
(This really was not a "repair")