Models > CVE1400W > Instructions

CVE1400W Jenn-Air Cooktop - Instructions

Jump to:

All Instructions for the CVE1400W
46 - 60 of 166
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
James from Dunnellon, FL
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
The 6in burner would go to max heat regardless of the setting.
Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
BETH from COUNCE, TN
Parts Used:
12001676
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Boone, IA
Parts Used:
W10341820
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
replace fan switch
remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Falls City, NE
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
old burners, burning very uneven!
Pulled out the old, plugged in the new
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lois from Alpharetta, GA
Parts Used:
W10341820
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
fan switch pushed through, plastic housing broken
Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bruce from SOUTHBURY, CT
Parts Used:
12001676
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Jennair cooktop with coils lost one of its coil guides.
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
marie from WATERBURY, CT
Parts Used:
W10291024
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
my first order a small drip bowl
came only I had to order the set again
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from ARCADIA, FL
Parts Used:
W11120791
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from Temple, TX
Parts Used:
W11120791
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burned burner control out of warranty
switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Batavia, NY
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Broken Surface Burner control
Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
alphonso from plainfield, IL
Parts Used:
WP71003558
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Lynn from Chester, SC
Parts Used:
WP707929, W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Burner was not working & needed new grease filter
Parts arrived very quickly & the installation was quick & easy. Will order again.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from Chehalis, WA
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Martin from Alexandria, VA
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joyce from Oceanside, CA
Parts Used:
WPY04100166
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CVE1400W
46 - 60 of 166