C306 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ralph from Manteca, CA
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Fan switch would not turn off
Disconnect power cord first. I remove the air fan cover to get to the two screws which hold the fan switch and burner knobs. Remove burner knobs and and remove switch cover, disconnect wires to fan switch. Pry spring nuts off with screwdriver to get switch off. Pay attention to which way switch goes on so that it turns on in the right direction. Install spring nuts (they may look too small but they're not) using a deep small socket the size of the spring nuts tap the the socket with a small hammer and the nuts will be locked in place. Put everything back in place and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Natalie from North Reading, MA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
front burner stayed on high
We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Bourbon, MO
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Sparks shot out from under knob, then, no surprise, the burner didn't work
I've ordered parts from you twice now, and both times the service has been absolutely amazing!!!!!
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Now, on to how I did this without fire or electrocution:
Turned off breakers.
Grabbed a beer.
Removed two screws holding in plate.
Removed electrical connectors.
Removed two screws holding switch.
Put new switch in place with screws.
Reattached connectors.
Reseated plate & screws.
Turned on power & tested.
Finished beer and felt very manly.
The hardest part was getting the plate to re-seat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sophie from Warrenton, VA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed replacement. Old one was falling apart.
Removed old filter, dropped in the new one.
(This really was not a "repair")
(This really was not a "repair")
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from N.Eastham, MA
- Parts Used:
- WP7518P054-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
damaged grill grate
Not much to tell about installing a new grill grate.
Partselct.com was very prompt and efficient in sending out the part.
Partselct.com was very prompt and efficient in sending out the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brent from Rancho Santa Fe, CA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter was torn and bent
I just lifted out old filter, and put in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Traverse City, MI
- Parts Used:
- 12001129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The fan switch broke
remove gas valve knobs, removed two screws holding trim plate on lifted plate removed wires replaced switch and reversed the prior moves.
Very easy
Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from McALESTER, OK
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
vent fan cloging up
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.
removed cover pulled out filter ,replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Goshen, NY
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter couldn't be cleaned
This was a no-brainer: old filter out, new filter in. In addition to replacing an old, greasy filter, I found that the exhaust fan now draws cooking fumes much more efficiently. So why did I wait the 6 years since we moved into this house to do this???
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Valentine from Bow, NH
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch was no good
I remove fore screwsfrom the front panel. Then remove two screws to remove the switch and removed the wire plugs then put everything back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Santa Clarita, CA
- Parts Used:
- 12001129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Fan switch was broken internally.
After reading the other do-it yourselfers I knew it wasn't going to be an easy task. However, when I received my new switch I saw that the hook up and installation would be a snap. My only problem was removal of the old lock washers so I cut them off with my tin snips and once the new switch was attached to the plate I used a socket on the end of a three inch extension. I placed the socket over the new washer and gently tapped on the end of the extention until the washer was seated. It took about two or three taps on each washer and I was finished. Everything went pretty well. Total time to install was about ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Lafayette, LA
- Parts Used:
- 74011338, WP7518P054-60, 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn out / burned grill and components
very easy - not really a "repair" more of a face lift, although the grill was unusable.
Parts were perfect - Used it the same night.
Parts were perfect - Used it the same night.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from castle rock, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
electric element would not function
2 screws to remove
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
disconnect 220 v power
use long nose pliers to transfer 5 female spade terminals
use nut driver to r@r shaft nut
replace panel with 2 screws
Turn on power and test!---OK!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Maplefalls, WA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter replacement.
Remove and replace grease filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Mountain Iron, MN
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter had hole wore through
Pulled the old one out & inserted the new one. Less than five minutes.
Was this instruction helpful to you?
Thank you for voting!