Models > C106-C > Instructions

C106-C Jenn-Air Cooktop - Instructions

Jump to:

All Instructions for the C106-C
121 - 135 of 155
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Woody from New Castle, VA
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Burner always on high, no temp. adjustment.
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Bothell, WA
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Rear butner no longer worked after liquid was spilled on range.
Just followed the instructions on this site... :) Unscrewed the front, removed old unit taking care of which wires went where, put in new unit. Voila.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Antonio from Davie, FL
Parts Used:
WP74008014
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door Hinge broken
I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharon from Kenai, AK
Parts Used:
WP707929
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The original filter was decomposing each time I washed it
I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sharyl K from Nampa, ID
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Left Rear Burner would not work
Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.
Was this instruction helpful to you?
Thank you for voting!
Customer:
June S from San Antonio, TX
Parts Used:
WP707929
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Filter was very old and falling apart.
The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from snellville, GA
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Burner stays hot
First turn off breaker, then take screws out switch assembly,take oid switch out, put new switch on,turn power on.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fred from Temple Terrace, FL
Parts Used:
700819
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Heat Errosion
Wife installed them, they just snap into place on the Rock Grate.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Cayce, SC
Parts Used:
WP707929
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Filter worn out, exhasut fan kept going off
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete
Was this instruction helpful to you?
Thank you for voting!
Customer:
richard from white castle, LA
Parts Used:
707704K, WPY707985
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
bearing went out in blower motor
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kris from Murfreesboro, TN
Parts Used:
WP74008014
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
oven door didn't shut completely
We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Port aransas, TX
Parts Used:
W11120791
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Rear Burner Was Not Functioning
Used a multimeter to determine that power was going to the surface burner infinite switch. Then determined that power was not going from the output side of the switch to the burner element. Turned power to range off at the breaker box. Removed eight screws total on range top, four on the cartridge side, two located on back of control plate where the downdraft vent is located and two on the double fixed burner side. Raised the range top to gain access to the infinite switch assemblies. Removed to torx head screws retaining the infinite switch and then disconnected the five wires on the bottom one at a time, making sure to replace in the exact location on the new switch. Installed torx screws in the new switch and installed all screws back into range top. Reinstalled cartridge and burners and turned power back on. Tested rear burner and all functioned properly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Woodland Park, CO
Parts Used:
W11120791
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Burner was very hot regardless of setting
Your site helped me determine the problem. You included a video of how to do the repair. The replacement of the parts went just as expected. The parts came quickly and were the correct parts. I could not have asked for a better experience. (I replaced two switches because the knob was loose on the othe one).. Thanks.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Hugh from Albuquerque, NM
Parts Used:
WP74008014
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Door would not close
Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dolores from Penrose, CO
Parts Used:
WP74008014
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
hinge broke on bottom oven door.
sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the C106-C
121 - 135 of 155