CVE4370W Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from ARCADIA, FL
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from GAITHERSBURG, MD
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
burner control stopped functioning.
Replaced the control.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randall from Colorado Springs, CO
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner would not turn off
It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charlotte, NC
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEITH from SALT LAKE CITY, UT
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken burner grill element
plugged new one in
Was this instruction helpful to you?
Thank you for voting!
Burner was not working & needed new grease filter
Parts arrived very quickly & the installation was quick & easy. Will order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emile J from Mahwah, NJ
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Range top fan switch shorted and started to burn.
Turned off power to range top. Two screws to lift the control area. One snap on was burned off.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Escalon, CA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old switch became brittle with age and broke. There were two plastic cylinders that held a spring loaded bearing to operate the contact point. It became brittle because of age and it broke.
I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Chehalis, WA
- Parts Used:
- W11120791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
burned up switch
Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Control switch would not operate
Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Ironton, OH
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defetive fan switch
throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martyn from Middletown, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Batavia, NY
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Broken Surface Burner control
Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Temple, TX
- Parts Used:
- W11120791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned burner control out of warranty
switch power supply off at breaker panel
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
unscrew control box assembly from stove
slide control out of stove
unscrew burner control out of assembly
transfer wiring from old control to new in same relative location
reassemble in reverse order
restore power
test burner in all positions
Was this instruction helpful to you?
Thank you for voting!