JGC8536ADB Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Juan J, from UNIVERSAL CTY, TX
- Parts Used:
- 74007735
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Needed use of penetrate lubrication
Removed two screw securing wburner and disengage igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John L from FAIR OAKS, CA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the gas burner head needed to be rerplaced due to the sparker not functioning properly
Ordered a replacement, removed the old burner and installed the new one. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from MCKINNEY, TX
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Knobs for the cooktop burners did not fit so I have returned them and still do not have use of all burners due to lack of knobs
Could not put a square peg into a round hole....parts did not fit and I do not know how to find the model number but the knob has two flat sides.l....the knobs you sent did not.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from PRATTVILLE, AL
- Parts Used:
- 74007734
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode not working.
Removed two screws and slipped the electrode connection off. Then reserved the process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from BRANCHBURG, NJ
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The knob does not go down; it sticks up too high. Question? Maybe knob is not for position 2. Does it matter which place you put it on?
I tried to put knob on number 2 location. Looks like I need number 1 knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from EADS, TN
- Parts Used:
- 74007736
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!
Voila!
Was this instruction helpful to you?
Thank you for voting!
Igniter clicked but burner would not light
Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from MISSION VIEJO, CA
- Parts Used:
- WP8286828, WP74007753
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
strickers stayed on when flames turned off
Had to remove the stainless cook top from the base. Required taking off all burners. All the screws were rusted in place so had to cut off the heads with dremmel and then drill out the screw from the aluminum base. Then remove cook top after burns taken off. Cook top is double sided taped to the base, so just pull hard and it comes off.
Replace the spark control module. make sure to do wires 1 at a time as they are not in a housing.
Replace the spark control module. make sure to do wires 1 at a time as they are not in a housing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Potomac, MD
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitors with VERY weak sparks (2 Burners)
Should have read the partselect instructions first 1.) unplugged range 2.) unscrewed (torque screws - good thing I had some) burners - one screw was corroded into the top and snapped - will require a drill to remove and replace metal screw. 3) slid electrical wire from contact 4.) unscrewed (with phillips) Burner Electrode assembly (also corroded - took some force) replaced electrode assy and reversed steps. Works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Rochester, NY
- Parts Used:
- WP74007749
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I lost the cap
after I received the cap in the mail, I removed the grillwork and set the cap in place. then replaced the grill and my wife fixed my supper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from neuvo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Granite Bay, CA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my knob broke
There is really nothing to replace a stove knob. What I was impressed with was the speed in which the knobs came to my house, the very next day from the day I ordered them.
Thanks a ton!
Thanks a ton!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cresco, PA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range would not light.
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Overland Park, KS
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The ignitor went out on one of the burners of the gas range
Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hendersonville, NC
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor cracked and would not light
Simply removed the old ignitor and install the exact replacement part. Work great.
Was this instruction helpful to you?
Thank you for voting!