CVG2420B Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Ranchos de Taos, NM
- Parts Used:
- Y705823
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burners kept clicking after ignited
After I bought this part, installed it and the clicking still did not stop I finally found the problem. If your ignitor can still click then it's still good. The problem is the electric connection between the head burners and the base burners (Top Assembly diagram). Put a little weight on the head burner while grabbing it with your hand and grind it into the base burner with a little twisting motion. Repeat for all 4 burners. Presto! (you could be more professional and use steel wool or sandpaper to.)
If you stll want to know how to install this part begin by removing the control panel bracket #24. Then remove the glass top w/seal #9 (after removing the knobs). You may have to tease this out because the rubber seal is sticky. The switch plate #14 comes off after removing 2 obvious screws at each end and 2 not-so-obvious star screws attaching it to the manifold #6. Remove the spark module by removing 2 of the 3 screws and sliding it out of the 3rd screw.
If you stll want to know how to install this part begin by removing the control panel bracket #24. Then remove the glass top w/seal #9 (after removing the knobs). You may have to tease this out because the rubber seal is sticky. The switch plate #14 comes off after removing 2 obvious screws at each end and 2 not-so-obvious star screws attaching it to the manifold #6. Remove the spark module by removing 2 of the 3 screws and sliding it out of the 3rd screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnnie from Daphne, AL
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Grease Filter For Downdraft Stove Top
Lift off blower vent cover. Lift out old filter. Clean walls and bottom of down draft using degrease soap and warm water. Dry. Discovered my grease filter will not install diagonally as shown in unit manual. Decided to drop into downdraft and put in front of fan suction. Found this left a gap at the top of fan suction that was not covered by the filter. Cut piece of wood 1 inch thick and width and length to drop down in the downdraft and lay on bottom. Set filter on top of wood in front of the fan suction. Verified that fan suction would pull filter tight against the opening by turning fan on and off. Put vent cover back over downdraft and told wife I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary H. from Appleton, WI
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter was starting to come apart from frequent cleaning.
I removed the center vent and inserted the filter...easy as pie...I went to your website and everything was there in an easy to follow way that even I could understand, my husband was totally impressed that I took care of it on my own....silly man.....it was so easy and delivery was extremely quick....so simple....thank you for making it so!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Birmingham, AL
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn grease filter
Replaced the filter which required no tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Chandler, TX
- Parts Used:
- WPY707985, 715957K, WP71003558
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
high blower vibration
blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph R. from Greenville, SC
- Parts Used:
- W11715914
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Plastic knob broke for the second time since cooktop was installed.
The entire cooktop had to be removed and taken apart to replace fan switch. I am thankful that this replacement part was available (slightly different than original part) through PartSelect.com since my local appliance parts store told me the part was no longer available.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from CHANTILLY, VA
- Parts Used:
- WPY706012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter broke
Ordered a replacement grease filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from JUNO BEACH, FL
- Parts Used:
- WPY706012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the filter screen was worn out and needed tp be replaced.
I merely lifted the downdraft cover and inserted the new screen as
directed. THANK YOU FOR YOUR PROMPT RESPONSE TO MY ORDER.
directed. THANK YOU FOR YOUR PROMPT RESPONSE TO MY ORDER.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Albany, GA
- Parts Used:
- Y706005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratched up grill on stove top
Just needed to replace a scratched up grill on my stove top. The black paint was scratched off and looked horrible. You site made it very easy to find what I needed and it got here in two days. If I had known it was going to be that quick and easy, I would've done it a long time ago! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elsie from OLATHE, KS
- Parts Used:
- WPY706012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old filter was falling apart
Just placed new filter in slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Mullica Hill, NJ
- Parts Used:
- Y706005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bashed Air Grill
Took the old one out, plopped the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Leesburg, VA
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace old grease filter
very easy slip in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Mount Sinai, NY
- Parts Used:
- WPY706012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement filter for jenn-aire
the filter fit because the scale in the photo allowed me to choose which one to buy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from aurora, CO
- Parts Used:
- Y705823
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Replace igniter
Pull the knobs, undo the torx nuts, fish out the ones I dropped into the cooktop; pull the panel to reveal the igniter module; undo the three nuts holding it - then transfer the wires one-by-one to the new module; fish out the screws with the magnet; secure the new igniter; replace the panels; redo the torx nuts; fish out the once I drop (AGAIN) and we're good to go. I was almost out of matches. The most useful tool was the magnet on a stick - my fingers are too big for the spaces I had to get into. Anyone can do this, and it saves money...
Was this instruction helpful to you?
Thank you for voting!